Buhler FK370 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 60

background image

16” Backsaver Auger

ASSEMBLY INSTRUCTIONS – cont’d.

26.

Pages 40 & 41. Attach the 139” hydraulic hoses (#5) to the relief valve (#12)
bolted to the winch hydraulic motor. These hoses run down the tube, alongside
the input box and connect to the left side ports on the top of the valve. The winch
has a pressure relief valve so the hoses must be connected to the correct ports.
Check hydraulic system drawing to verify. Two 79” hoses (#4) connect to the
sides of the valve. These both attach to the tractor.

27.

The relief valve (page 40, #12) bolted to the winch hydraulic motor should be
adjusted before using. The power is adjusted on the control screw at the top of
the unit. Loosen the hex nut on the threaded shaft and adjust using an Allen
wrench. Adjust so you have enough power to lift the empty intake auger off the
ground. Lock the setting in place with the hex nut. The winch speed is adjusted
by a control screw on the side. Remove the plug and adjust the speed with an
Allen wrench. Adjust so the intake auger lifts slowly and replace the plug.

28.

The standard drive position for the drive shaft (page 35, #85) in the rpm gearbox
(page 35, #26) is in the outer coupler. The center coupler on the gearbox is used
to reverse the flighting. This should be used to clean out the auger only. There
are two solid plugs in the side of the gearbox. The higher of the two plugs should
be removed and replaced with a 90 degree vent plug (page 50, #17). The lower
of the two plugs acts as an oil level plug.

29.

Re-check and tighten all bolts.

30.

Immediately after setting up the auger, hook it up to a tractor. Raise and lower
the auger three or four times to purge all the air out of the hydraulic line to the lift
cylinder. This will help to prevent the auger from settling when you have it in
working position above a bin.

ALERT:

Always check to see that both ends of the PTO shaft are securely

attached every time the auger is used. This should always be done with the
tractor engine shut off. When transporting the auger, disconnect the PTO shaft
from the tractor. The PTO holder at the end of the hitch is used to hold the PTO
during transport.

Do not run the auger with the intake auger in the transport position. Doing this
will damage the u-joint between the intake auger and the input box.

16

«
...
17
18
19
20
21
...
»

Содержание FK370





























































Отзывы:

Нет отзывов

Похожие инструкции для FK370

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: IBEX Страницы: 4

Бренд: Ultrawave Страницы: 30

Бренд: Ultrasound Technologies Страницы: 12

Бренд: Yamaha Страницы: 29

Бренд: E-FLOR Страницы: 124

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

FUSION Equine DR II

Бренд: SOUND Страницы: 178

Бренд: Cooper Страницы: 10

Бренд: Korg Страницы: 32

Бренд: Launch Страницы: 15

Бренд: RayLight Страницы: 31

Бренд: PLUSLITE Страницы: 13

BlitzForce XXLC-33-NH1

Бренд: Task Force Tips Страницы: 16

Бренд: Walimex Pro Страницы: 7

Бренд: Adcraft Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды