Buhler FK370 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 60

background image

16” Backsaver Auger

OPERATING INSTRUCTIONS - CONT'D.

One-way flow control valve can be adjusted by loosening the hex nut on the side, and
turning on the screw with the machined end. Turning the screw in decreases the speed
the auger lowers, while turning it out increases the speed. The approximate initial
setting should be 3 ½ turns out from the tight position. When set, re-tighten hex nut to
set position.

NOTE

: Be sure that the valve is somewhat open before raising the first

time or auger will not lower.

Be sure there is always some tension on the flighting by adjusting the end thrust bearing
at the upper end of the auger.

ALERT:

Always lower auger before transporting and allow the weight of the

auger to rest on the undercarriage and not the hydraulic cylinder.

Be certain to turn jack sideways when towing auger.

ALERT:

Disconnect the PTO shaft from the tractor and pin it in place in the PTO

holder when towing or maneuvering the auger. This will prevent possible damage to the
PTO shaft during cornering.

ALERT:

If the PTO shaft angle exceeds 50

°

during a tight turn, the constant

velocity joints will be fractured and will likely fail shortly thereafter during operation.

PTO shear bolts (2 required) – 3/8" x 1" hex bolt (grade 8)

ALERT:

When towing the auger, never exceed 32 kilometers per hour.

This 16” auger has a total weight of about 13,000 pounds and a hitch weight of about
2,700 pounds. You must have a vehicle rated for this amount of weight to transport this
auger.

21

«
...
22
23
24
25
26
...
»

Содержание FK370





























































Отзывы:

Нет отзывов

Похожие инструкции для FK370

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: UNIA Страницы: 62

Бренд: R2 Страницы: 20

Бренд: B&G Страницы: 3

Бренд: J.P. SELECTA Страницы: 32

Бренд: Quick Страницы: 24

Бренд: JDS Uniphase Страницы: 144

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 14

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды