Buhler FK370 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 60

background image

16” Backsaver Auger

MAINTENANCE & LUBRICATION

Check condition of winch cable regularly. Be sure it is lubricated. Replace cable if you
notice any broken strands.

Check to see that there is no downward bow in the main tubes at the start of every
augering season. Re-tension cables if required as per the assembly instructions. This
should also be checked immediately after hauling the auger for a long distance.

Use a high temperature grease for all lubrication.

Lubricate the PTO shaft as per instruction sheet.

Check grease on end thrust bearing to be sure it is running smoothly and freely.
Remove cap and grease at the start of every season.

Check hydraulic lines frequently for leaks or damage.

Grease universal joint in intake auger after every eight hours of use.

Grease the U-joint connecting the two gearboxes about every 8 hours. Do regular
checks on the oil level in the gearboxes. Fill if necessary to the height of the side plug
using SAE 90 oil. Because the gearbox runs in the grain, it is difficult to see any oil
leaks so regular checks should be done. The reducer gearbox requires 2.5 litres of
75W–90 synthetic oil. Reducer gearbox should be serviced every year or every 1000
hours. The hydraulic winch gearbox requires 2.5 litres of 80w-90 gear oil.

ALERT:

When replacing bearings or tightening a loose bearing collar, always

tighten collar in the direction of shaft rotation using a center punch or a similar tool.

Recommended tire pressure is 45 to 50 psi (max. 60 psi).

23

«
...
24
25
26
27
28
...
»

Содержание FK370





























































Отзывы:

Нет отзывов

Похожие инструкции для FK370

Бренд: Qingdao H.Y Страницы: 6

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Navman Страницы: 17

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Gainsborough Страницы: 2

Бренд: Unex Страницы: 5

Бренд: SAMCHULLY Страницы: 48

Бренд: Gallagher Страницы: 6

Sonopuls HD 4050

Бренд: BANDELIN Страницы: 48

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: IDEAL Страницы: 12

Бренд: Keithley Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды