Buderus Logamax plus GB142-24 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 68

background image

Please read thoroughly before installing and servicing

7215 0200 – 10/2007 US/CA (en)

For registered installers

Installation instructions

Condensing gas boiler
Logamax plus GB142-24/30/45/60

CAUTION!

Before putting the boiler into operation read this manual carefully.

WARNING!

Improper installation, adjustment, alteration, service or maintenance
can cause injury, loss of life or property damage. Refer to this manual.
For assistance or additional information consult a qualified installer,
service agency or the gas supplier.

CAUTION!

The operating manual is part of the documentation that is delivered to
the installation's operator. Go through the information in this manual
with the owner/operator and make sure that he or she is familiar with
all the necessary operating instructions.

NOTICE!

In the Commonwealth of Massachusetts this boiler must be installed
by a licensed Plumber or Gas Fitter.

–

Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other boiler.

– What to do if you smell gas

•

Do not try to light any boiler.

•

Do not touch any electrical switch; do not use any phone in your
building.

•

Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

Warning: If the information in these instructions is not
followed exactly, a fire or explosion may result caus-
ing property damage, personal injury or loss of life.

1
2
3
...
»

Содержание Logamax plus GB142-24





































































Отзывы:

Нет отзывов

Похожие инструкции для Logamax plus GB142-24

Saga Industrial 800 0854

Бренд: OSO HOTWATER Страницы: 112

Бренд: Varmebaronen Страницы: 40

Бренд: Radijator Страницы: 109

Бренд: geminox Страницы: 24

MultiTemp MR Series

Бренд: HydroTherm Страницы: 36

Бренд: Ferroli Страницы: 36

Бренд: Buderus Страницы: 108

Бренд: Biodom Страницы: 61

Бренд: Bryant Страницы: 20

Бренд: HTP Страницы: 56

Бренд: Immergas Страницы: 148

VICTRIX 115 1 I

Бренд: Immergas Страницы: 146

Gold 15 Heat ErP

Бренд: Potterton Страницы: 16

Бренд: Alternate Heating Страницы: 31

Бренд: Alternate Heating Страницы: 64

Бренд: Knight Страницы: 80

Бренд: Knight Страницы: 80

Бренд: iMettos Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды