Brother XL-2121 страница 35 Скачать руководство пользователя

Страница: 35 / 63

STRAIGHT AND ZIGZAG STITCHING

——————————————————————————————————————————

Zigzag Stitching

■

Zigzag Stitch

Turn the pattern selection dial to zigzag stitch,
and then start sewing.

We recommend that you sew using the Straight
Stitch at the beginning and end of the Zigzag
Stitches.
(This acts as a reinforcement stitch.)

■

Zigzag (Satin) Stitch

You can use the zigzag (satin) stitch for making
decorative stitches.
When sewing a zigzag (Satin) stitch, use a slightly
looser upper-thread tension to produce more
beautiful stitches.

You can adjust the length of the Zigzag (Satin)
Stitch using the buttonhole fine-adjusting screw.

Buttonhole fine adjusting screw

For a longer stitch length, turn the
buttonhole fine-adjusting screw with a large
screwdriver in the + direction.

For a shorter stitch length, turn the
buttonhole fine-adjusting screw with a large
screwdriver in the - direction.

Stitch Name

Pattern

Stitch

Length

[mm (inch.)]

Stitch

Width

[mm (inch.)]

Zigzag Stitch

1.5 (1/16)

3.0 (1/8)

Zigzag Stitch

2.0 (1/16)

5.0 (3/16)

Zigzag (Satin)

Stitch

0.5 (1/32)

5.0 (3/16)

Содержание XL-2121
































































Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды

Brother XL-2121, Руководство по эксплуатации

Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды