Brother XL-2121 страница 42 Скачать руководство пользователя

Страница: 42 / 63

■

Securing the Stitching and Cutting the
Buttonhole

To secure the stitching, turn the material 90
degrees counterclockwise and sew Straight
Stitches to the end of the front bar tack of the
buttonhole.

Remove the material from the machine. We
recommend that you put pins across both
ends of the buttonhole as protection against
cutting the stitches.

Cut an opening in the middle of the
buttonhole with a seam ripper tool. Be careful
not to cut through any stitches.

Adjusting Buttonholes

If the stitching on the two sides of the buttonhole is
not the same, you can make the following
adjustments.

After sewing the left side of the buttonhole,
stitch the right side and observe the feeding.

Right row

If one side is too coarse or fine compared with
the other side, adjust the buttonhole fine
adjusting screw as shown below.

Buttonhole fine-adjusting screw

If the right side is too coarse, turn the
buttonhole fine adjusting screw with a large
screwdriver in the - direction.

If the right side is too fine, turn the
buttonhole fine adjusting screw with a large
screwdriver in the + direction.

• This adjustment allows both sides of the

buttonhole to be the same.

●

When using the seam ripper to open the
buttonhole, do not put your hand or
finger in the path of the ripper. The
ripper may slip and injure you.

CAUTION

Содержание XL-2121
































































Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды

Brother XL-2121, Руководство по эксплуатации

Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды