Brother XL-2121 страница 43 Скачать руководство пользователя

Страница: 43 / 63

SEWING BUTTONHOLES AND BUTTONS

———————————————————————————————————————

Sewing Buttons

Measure the distance between the
buttonholes and set the pattern selection dial
to the Zigzag Stitch for the width you want.

Remove the power supply plug from the
outlet.

Change the foot to the Button sewing foot.

Place the darning plate on the needle plate.

Connect the power supply plug into the wall
outlet.

Put a button between the foot and the fabric
and make sure that the needle enters the holes
without hitting the button. If it hits, see Step

At a slow speed, sew about 10 stitches.

Remove the material from the machine. Cut
the upper and lower threads and tie both
threads at the back of the material.

Stitch

Name

Pattern

Stitch

Width

[mm (inch.)]

Foot

Other

Zigzag

Stitch

3.0

(1/8)

Button

Sewing

Foot

Darning

Plate

Zigzag

Stitch

5.0

(3/16)

Zigzag

(Satin)

Stitch

5.0

(3/16)

●

Make sure the needle does not hit the
button during sewing. The needle may
break and you may be injured.

CAUTION

Содержание XL-2121
































































Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды

Brother XL-2121, Руководство по эксплуатации

Результаты поиска

Содержание XL-2121

Отзывы:

Похожие инструкции для XL-2121

Бренды по названию

Популярные бренды