Bradley Bradmar 700 Series Скачать руководство пользователя страница 31

Страница: 31 / 33

Installation

Phenolic Privacy Restroom Partitions, Floor-to-Ceiling — Series 700, — 69", 72" & 69"/72" Tall

Bradley •

HDWC-INSTR-045 Rev. A: ECO 20-14-002S

6/25/2021

Flat Strike at Wall – Outswing

Flat Strike at Pilaster – Outswing

Using the flat strike as a template, mark the hole

locations on the wall . Remove the flat strike and drill a

Ø1/4" hole (min . 2" (51) deep) at each hole location .

Using the flat strike as a template, mark the hole

locations on the pilaster . Remove the flat strike and drill a

Ø11/64" hole (min . 1/2" (13) deep) at each hole location .

Insert the plastic anchors in all of the holes and secure

the flat strike to the wall using the #10 x 2" screws

provided .

Secure the flat strike to pilaster wall using the

#10 x 1" screws provided .

Refer to Step G for installing the keeper and Step K for

installing the dampening strip .

Refer to Step G for installing the keeper and Step K for

installing the dampening strip .

With the door in the closed position, place the

non-notched edge of the flat strike against the wall . The

notched edge of the door should fit into the notch on the

flat strike . The top edge of the flat strike and door should

align along with the front faces .

With the door in the closed position, place the

non-notched edge of the flat strike against the pilaster .

The notched edge of the door should fit into the notch

on the flat strike . The top edge of the flat strike and door

should align along with the front faces .

Wall

9a Door Hardware for Outswing Doors (continued)

Pilaster

Flat Strike

Outswing Door

Flat Strike

Outswing Door

Содержание Bradmar 700 Series


































Результаты поиска

Содержание Bradmar 700 Series

Отзывы:

Похожие инструкции для Bradmar 700 Series

Бренды по названию

Популярные бренды

Bradley Bradmar 700 Series, Руководство по установке

Результаты поиска

Содержание Bradmar 700 Series

Отзывы:

Похожие инструкции для Bradmar 700 Series

Бренды по названию

Популярные бренды