Bradley Bradmar 700 Series Скачать руководство пользователя страница 29

Страница: 29 / 33

Installation

Phenolic Privacy Restroom Partitions, Floor-to-Ceiling — Series 700, — 69", 72" & 69"/72" Tall

Bradley •

HDWC-INSTR-045 Rev. A: ECO 20-14-002S

6/25/2021

9a Door Hardware for Outswing Doors

Local codes vary from state to state. Check your local codes before installing the

door pulls and coat hook.

When the door latch is correctly installed, the red indicator color should appear

when the latch is in the closed position.

From the back side of the door, align the two mounting posts on the slide latch with the holes in

the door . Hold or tape in place .

From the front side of the door, align the black disk with the countersunk holes at top and sides

with the holes in the metal handle . Place the longer flat head Phillips drive screws (provided)

through the side holes in the black disk, metal handle, and door . Secure to the mounting posts in

the side latch .

Place the square pin into the back of the indicator circle . Verify the red indication color is in the

proper position so that red will appear when the latch is in the closed position .

Using the top countersunk hole in the black disk as a template, drill a Ø9/64” pilot hole, 1/2" (13)

deep and secure to the door using the small flat head Phillips drive screw (provided) .

Slide the square pin through the large center hole in the door and into the slide latch on the other

side .

Again, verify the red indication color is in the proper position to appear when the latch is in the

closed position before securing the indicator circle with the small tabs over the black plastic piece .

E
F

Keeper

.030"

( .762)

With the door in the closed position, place the keeper on the pilaster so the leading edge is .030" ( .762) from the

pilaster edge and the slide latch moves freely over the keeper . Using the keeper as a template, drill (2) Ø15/64"

pilot holes, 5/8" (16) deep . Secure with the #14 x 5/8" Torx screws provided .

2 .25" Ref .

(57)

41" Ref . (1041)

A .F .F .

Front

View

Front

View

Back

View

Back

View

#14 x 5/8"

Torx Screws

Pilaster

.125"

(3 .175)

Door

Mounting

Posts

Square

Black

Disk

Содержание Bradmar 700 Series


































Результаты поиска

Содержание Bradmar 700 Series

Отзывы:

Похожие инструкции для Bradmar 700 Series

Бренды по названию

Популярные бренды

Bradley Bradmar 700 Series, Руководство по установке

Результаты поиска

Содержание Bradmar 700 Series

Отзывы:

Похожие инструкции для Bradmar 700 Series

Бренды по названию

Популярные бренды