Bowflex TreadClimber TC20 Скачать руководство пользователя страница 43

Страница: 43 / 95

16. Remove the Motor Control Board and replace.

17. Re-install the two Phillips head screws into the new Motor Control

Board.

18. Connect AC Power Wires.

19. Connect the Tach Cable.

Note:

If present, the Motor Fan is not used for the operation of the machine. The Fan Power Wires should not be connected to the new Motor

Control Board. If desired, the Fan Assembly can be removed from the machine. Otherwise, be sure to place the Wires away from the Motor

Control Board.

20. Connect Motor Power Wires. NOTE: Red wire connects to terminal labeled “M+RED”. Black wire connects to terminal labeled “M-BLK”.

21. Connect the I/O Cable to the Motor Control Board.

22. Replace the right Side Cover and screws.

23. Connect the Cylinder and secure with the lower Cylinder mounting bolt.

24. With assistance, carefully set the machine upright.

Do not move the machine without aid. Injury to you or damage to the machine can occur. The Treadles and Walking Belts can abruptly

move. To avoid possible serious injury, keep hands away from the inside of the Treadles and the edges of the Walking Belts.

25. Replace the right Pivot Cover, the Motor Cover, and the Rear Cover.

26. Replace Power Cord and test machine for proper operation. NO CALIBRATION IS NECESSARY for this model.

27. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.

Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s

Manual.

MOTOR

POWER

WIRES

FAN

(not provided on newer

machines)

TACH

BLACK

RED

MOTOR CONTROL BOARD

WIRES

AC POWER

(I/O) CABLE

INPUT/ OUTPUT

Содержание TreadClimber TC20
































































































Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды

Bowflex TreadClimber TC20, Руководство по обслуживанию

Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды