Bowflex TreadClimber TC20 Скачать руководство пользователя страница 34

Страница: 34 / 95

6. Remove the 5 indicated screws using a #2 Phillips screwdriver from the left

Side Cover.

7. Slide the left Side Cover off of the machine.

8. On the Motor Control Board, disconnect the Motor Power Wires by pulling

straight out on the Connectors – do not pull on the wire itself. Push the loose

wires through to the Motor compartment. Using a #2 Phillips screwdriver, detach

the Grounding Wire from the Base Assembly.

Note:

The Motor Control Board is located under the right Treadle.

9. Remove the Drive Belt. Turn the Drive Pulley clockwise while forcing the Drive

Belt to the outside. Belt will come off of the Drive and Motor Pulley.

Keep fingers out of any pinch opportunities when turning the Pulleys.

Grounding Wire

Motor Power Wires

Motor Control

Board

Motor

Motor Pulley

Drive Pulley

MOTOR

POWER

WIRES

FAN

(not provided on newer

machines)

TACH

BLACK

RED

MOTOR CONTROL BOARD

WIRES

AC POWER

(I/O) CABLE

INPUT/ OUTPUT

Содержание TreadClimber TC20
































































































Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды

Bowflex TreadClimber TC20, Руководство по обслуживанию

Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды