Bowflex TreadClimber TC20 Скачать руководство пользователя страница 46

Страница: 46 / 95

7. Tilt the machine carefully onto the right side.

Do not move the machine without aid. Injury to you or damage

to the machine can occur. The Treadles and Walking Belts can

abruptly move. To avoid possible serious injury, keep hands

away from the inside of the Treadles and the edges of the

Walking Belts.

8. Using the 5 mm hex wrench, remove the lower mounting bolt from

the Cylinder.

9. Disconnect the Cylinder from the Treadle indicated by the arrow.

Leave the top attached.

10. Using a #2 Phillips screwdriver, remove the 5 indicated screws

from the Side Cover.

11. Slide the Side Cover off of the machine.

12. Using the 5 mm hex wrench, loosen the Belt Tensioning Screws

on both Treadles (2 screws on each Treadle).

Note:

Be sure to record how many turns it takes to loosen the screws

to assist with reassembly.

13. Using a #2 Phillips screwdriver, remove the 6 indicated screws

from each of the Foot Support Platforms.

14. With assistance, carefully set the machine upright.

Do not move the machine without aid. Injury to you or

damage to the machine can occur. The Treadles and Walking

Belts can abruptly move. To avoid possible serious injury,

keep hands away from the inside of the Treadles and the

edges of the Walking Belts.

Содержание TreadClimber TC20
































































































Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды

Bowflex TreadClimber TC20, Руководство по обслуживанию

Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды