Bowflex TreadClimber TC20 Скачать руководство пользователя страница 45

Страница: 45 / 95

1. Unplug the power cord from the machine and wait 5 minutes.

2. Using a #2 Phillips Screwdriver, remove the 2 indicated screws from the

Rear Cover.

3. Remove the Rear Cover.

4. Using a #2 Phillips screwdriver, remove the 2 indicated screws from the

Motor Cover. Lift up on the front of the Motor Cover, releasing it from the

Base Assembly. Slide the Motor Cover out from beneath the Treadles.

5. Using a #2 Phillips screwdriver, remove the 3 indicated screws from the

right Pivot Cover.

6. Remove the right Pivot Cover and Spacer.

To reduce the risk of electrical shock or unsupervised usage of the equipment, always unplug the power cord from the wall outlet

and the machine and wait 5 minutes before cleaning, maintaining or repairing the machine. Place the power cord in a secure

location.

Motor Cover

Содержание TreadClimber TC20
































































































Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды

Bowflex TreadClimber TC20, Руководство по обслуживанию

Результаты поиска

Содержание TreadClimber TC20

Отзывы:

Похожие инструкции для TreadClimber TC20

Бренды по названию

Популярные бренды