Control Center
DVD
f
Slot-loading progressive scan: NTSC Region 1
Plays 12cm Discs
f
DVD Video (DVD, DVD
±
RW/
±
R),
DVD-Audio, CD (CD, CD-R, CD-R/W, MP-3)
AM/FM Tuner
f
AM tuning range: 530kHz–1610kHz
FM tuning range: 87.5mHz–107.9mHz
27 presets in 3 banks of 9 (mixed AM and FM)
External Sources
Aux Audio
f
Analog and optical digital audio in and out
Cable/Sat
f
Composite video and S-Video in
Analog, coaxial, and optical digital audio in
Changer
f
Composite video and S-Video in
Analog, coaxial, and optical digital audio in
VCR/PVR
f
Composite video and S-Video in
Analog, coaxial, and optical digital audio in
Composite video and S-Video out
Analog and optical digital audio out
TV
f
Composite video and S-Video in
Analog and optical digital audio in
Front
f
Composite video and S-Video in
Analog and optical digital audio in
Component
f
Y/Pr/Pb assignable to any source
Outputs
Monitor Out
f
Composite, S-, and Component Video
Zone 2
f
Analog audio selectable fixed or variable
12v Trigger
f
1/8-inch (3.5mm) jack; tip positive
IR Repeaters (2)
f
1/8-inch (3.5mm) jack
Headphone Out
f
1/8-inch (3.5mm) jack
To Subwoofer
f
Multi-pin connector
Subwoofer
10-inch (254mm), front-firing DCD™ driver
Down-firing dual flared ports
Amplification for subwoofer and six speakers
Color-coded, phase inversion proof connectors for all speakers
Multi-pin connector to Control Center
.
.
.
.
.
.
SPECIFIC
A
TIONS
63
The Avidea Remote Control is not recognized by the FreedomEdit software
• Make sure the serial cable is properly connected. (See ‘FreedomEdit’ on page 32 of the Avidea Remote
Control Setup and Use Guide.)
• Disconnect other equipment connected to the serial ports, e.g., PDAs.
• Plug the serial cable in another serial port.
• Try to connect multiple times.
Remote Control buttons are not sending the correct commands
• Check if you have defined the correct brands for your Devices. (See ‘Entering Codes for Other Devices’ on
page 21 of the Avidea Remote Control Setup and Use Guide.)
• Check whether the button of the Device is learned properly. (See ‘Learning Commands’ on
page 24 of the Avidea Remote Control Setup and Use Guide.)
• Check whether the macro is recorded properly. (See ‘Recording Macros’ on page 28 of the
Avidea Remote Control Setup and Use Guide.)
The Avidea Remote Control will not switch modes
• Replace the batteries. When the batteries are low, the Avidea Remote Control prevents you from switching
to customizing modes so that no customization can get lost.
The Avidea Remote Control is low on memory
• Revert the Avidea Remote Control. (See ‘Revert’ on page 17 of the Avidea Remote Control Setup
and Use Guide.)
The Avidea Remote Control’s configuration file is corrupted
• When this unlikely event occurs, you have to revert to the original configuration or use FreedomEdit to
download a new configuration file. All your customized commands and Devices will be lost and you will
have to reprogram your Avidea Remote Control. If you use FreedomEdit, it is advisable to make backup
copies of your customized configurations. (See ‘Revert’ on page 17 and ‘FreedomEdit’ on page 32 of the
Avidea Remote Control Setup and Use Guide.)
The Avidea Remote Control gives an error message
• If the error message ‘Invalid CF version or corrupt Flash!’ occurs:
• Use the Reset button on the back of the Avidea Remote Control. (See ‘How do I reset the Avidea
Remote?’ on page 35 of the Avidea Remote Control Setup and Use Guide.)
• Try to recover the Avidea Remote Control Configuration File (NCF) by downloading a backup
copy or the default file from FreedomEdit. (See ‘FreedomEdit’ on page 32 of the Avidea Remote
Control Setup and Use Guide.)
• Go to the Boston Acoustics website http://www.bostonacoustics.com/avidea for
more information.
The volume of my Avidea system changes when I change channels on my cable box
• This is due to the nature of the programming found on cable. Higher numbered, digital channels with
Dolby Digital audio will not be as loud as the older, lower numbered analog channels. Unfortunately, there
is nothing you can do to correct this problem.
The rear/center speaker is not on when listening to DVD-Audio discs
• DVD-Audio is a 5.1-channel format. The rear/center speaker cannot be activated when playing
a DVD-Audio disc.
The rear/center speaker is not on with certain cable or satellite channels
• Certain cable and satellite programs provide Dolby Digital 2.1 audio (stereo with subwoofer). Avidea will
automatically use Dolby Pro Logic II to activate the center channel, rear/left, and rear/right speakers. The
rear/center speaker cannot be activated under these circumstances.
• If a program uses Dolby Digital 5.1, pressing the 5/6 touchscreen button will activate the
rear/center speaker.
The Avidea Remote Control does not respond to button presses
• Remove and reinstall one of the Remote Control’s batteries.
. . .
. . .
TROUBLESHOO
TING
62
SPECIFICATIONS
07
SECTION
06
SECTION
TROUBLESHOOTING
