bolid S2000M Скачать руководство пользователя страница 62

Страница: 62 / 64

FIRE AND ALARM CONSOLE

Event description

Displayed event name Category

Battery supply is out of range

BATTERY FAILED

Battery supply is restored

BATTERY RESTORED

AC power has been lost

AC POWER FAILED

AC power has been restored

AC POWER RESTORE

Device was restarted

DEVICE RESTART

The console has no response from the device through RS-485
interface

DISCONNECTED

The console has restored the connection with the device through RS-
485 interface

CONNECTED

Device shutoff from ring interface RS-485 branch

FAIL RS485 LINE

Device connection through RS-485 ring interface branch has restored

RST RS485 LINE

Short circuit in 2-wire addressable line

2WIRE LINE SHORT

Open-circuit failure in 2-wire addressable line

2WIRE LINE OPEN

Other troubles in 2-wire addressable line

2WIRE LINE TRBL

2-wire line restored after any failure

2WIRE LINE RST

The automatically launching mode of extinguishing equipment is off

EX MODE MANUAL

The automatically launching mode of extinguishing equipment is on

EX MODE AUTO

The pressure detector has signaled pressure rising

GAS PRESS SIGNAL

There is no expected pressure increase after launching pulse

PRESSURE FAILURE

Fire conditions have been detected

FIRE SIGNAL

The service is required for the detector (for example, the smoke
chamber of DIP-34A detector is dusted)

SERVICE REQUIRED

Temperature has exceeded the maximum value

TEMPERATURE HIGH

Temperature has fallen below the minimum value

TEMPERATURE LOW

Temperature has normal value

TEMPERATURE NORM

The heat sensor failure has detected

HEAT SENSOR FAIL

The heat sensor has been restored after failure

HEAT SENSOR RST

Voice notification is starting

NOTIFICATION ON

Voice notification is avoided

NOTIFICATION OFF

The pump is starting

PUMP ON

The pump cuts out

PUMP OFF

The pressure or water level is rising

LEVEL HIGH

The pressure or water level is falling

LEVEL LOW

The pressure or water level is in normal state

LEVEL NORMAL

The pressure or water level has exceeded the emergency threshold

LEVEL TOO HIGH

The pressure or water level has fallen below the emergency threshold

LEVEL TOO LOW

Auxiliary loop alarm

AUX ZONE ALARM

Auxiliary loop restored

AUX ZONE RESTORE

Zone disarmed. Arming is impossible due to detector being in
activated state

NOT READY TO ARM

Zone disarmed. Ready for arming.

READY TO ARM

The open-circuit failure of relay output load circuit has been detected

RELAY TRBL OPEN

The short circuit failure of relay output load circuit has been detected

RELAY TRBL SHORT

Содержание S2000M

































































Результаты поиска

Содержание S2000M

Отзывы:

Похожие инструкции для S2000M

Бренды по названию

Популярные бренды

bolid S2000M, Руководство по обслуживанию

Результаты поиска

Содержание S2000M

Отзывы:

Похожие инструкции для S2000M

Бренды по названию

Популярные бренды