bolid S2000M Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 64

background image

FIRE AND ALARM CONSOLE

58

State Description

Displayed

"ENTRY ALARM"

Entry zone alarm if entry delay has not elapsed

ENTR ALARM

"ENCLOSURE

TAMPERING"

Device enclosure tamper detector has been broken

TAM ALARM

"2-WIRE LINE

SHORT CIRCUIT"

Short circuit in "S2000-KDL" 2-wire addressable
line

2WRE SHORT

"2-WIRE LINE

TROUBLE"

Trouble in "S2000-KDL" 2-wire addressable line
(usually it is abnormal overvoltage)

2WRE TRBL

"DISCONNECTED

ALARM LOOP"

The communication between the console and alarm
loop or addressable detector or addressable
expander circuit being controlled has been lost. The
status of such zone is unknown and the console
cannot monitor this one.
It is typically happens when:
1) the communication between the console and
intrusion and fire alarm panels or “S2000-KDL”
controller connected via RS-485 line and
monitored present zone has been lost;
2) the communication between “S2000-KDL” and
addressable detector (expander) connected to its
2-wire line and controlled zone in question has been
lost

DISCONNECT

"CONFIGURATION

ERROR"

Type mismatch of 2-wire line connected
addressable device and value given in
"S2000-KDL" configuration, or mismatch of zone
type and type of device connected to "S2000-KDL"

CONFIG ERR

"FIRE TROUBLE"

Fire alarm system failure such as addressable
device internal problem (failure of DIP-34

А

optical

system), or "S2000-KPB" device mass and pressure
checkout circuit trouble

FIRE TRBL

"LOOP OPEN

CIRCUIT"

The breaking of alarm loop or addressable expander
circuit being controlled

TRBL OPEN

"LOOP SHORT

CIRCUIT"

The short circuit of alarm loop or addressable
expander circuit being controlled

TRBL SHORT

"ARMING HAS

FAILED"

Arming has failed due to the activated status of
detector

ARM FAILED

"DISARMED AND

NOT READY"

For alarm zones being controlled if disarmed. Zone
is not armed with the detector having been activated
and so being not ready for arming

NOT READY

"DISARMED"

Zone has been disarmed and the detector status is
not monitoring

DISARMED

"DISARMED AND

READY"

For alarm zones being controlled if disarmed. Zone
is not armed but it is ready for following arming

READY

«
...
56
57
58
59
60
...
»

Содержание S2000M

































































Отзывы:

Нет отзывов

Похожие инструкции для S2000M

Cody Universal 2

Бренд: Geba Tronic Страницы: 96

Бренд: LEGRAND Страницы: 9

Бренд: M&S Systems Страницы: 2

Бренд: Paradox Страницы: 47

Бренд: Guardian Страницы: 2

Бренд: PeopleKey Страницы: 19

Бренд: Alarm Lock Страницы: 8

Бренд: Penclic Страницы: 8

XK-1483-UABK24-R

Бренд: X-keys Страницы: 4

Бренд: Mighty Mule Страницы: 16

Interlogix TVK 800

Бренд: United Technologies Страницы: 76

Бренд: Bosch Страницы: 2

Бренд: Bosch Страницы: 2

Бренд: Bosch Страницы: 8

Бренд: Dippo Страницы: 32

Бренд: DESi Страницы: 14

Бренд: RCI Страницы: 6

Бренд: McIntosh Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды