Blue Seal Evolution Series Скачать руководство пользователя страница 86

Страница: 86 / 94

Appendix B: Gas Type Conversion

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

Main Burner Injector

Pilot Burner

Piezo Igniter

Thermocouple

Main Burner

Aeration Slide

Burner Adjustment Screw

Convection Oven

Carry out the following:-



Remove lower lintel at front of oven.



Open oven door and remove sole plate(s).



Loosen clamp bracket and remove main burner.



Remove thermocouple and piezo igniter from mount-
ing bracket. (For access purposes).



Disconnect pilot supply tube from pilot burner to ac-
cess pilot injector.

With Main Burner removed, ensure aeration gap is adjusted for type of gas being used as
shown in ‘Gas Specifications Tables’ at end of this section.

Remove pilot and main injectors and replace with correct size injectors as shown in ‘Gas
Specifications Tables’ at end of this section.

4. Refit

the

following:-



Re-connect pilot supply tube to pilot burner.



Re-connect piezo igniter and thermocouple to mounting bracket.



Refit main burner and secure clamp bracket.



Refit sole plate(s) and lower lintel.

NOTE:

There is no 'Low Fire' adjustment on the gas control valve for the GC Oven.



Refit the oven control panel.

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды