Blue Seal Evolution Series Скачать руководство пользователя страница 87

Страница: 87 / 94

Appendix B: Gas Type Conversion

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

Gas Regulators

- NAT Gas / LPG / Butane Only.

NOTE: The gas regulator supplied is convertible

between Natural Gas and LP Gas, but it’s
outlet pressure is fixed ex-factory and is
NOT to be adjusted.

- Town Gas Only.

Remove slotted cap from regulator.

Turn ‘On’ gas supply and appliance.

Adjust pressure adjusting screw to achieve correct burner operating pressure.

NOTE:

Operating pressure to be measured at manifold test point with two
burners operating at 'High Flame' setting.

Verify operating pressure remains correct (Re-adjust regulator if required).

Screw cap nut back onto regulator.

Gas Type Identification Label

On completion of gas conversion, replace gas type identification label located at:-

- Rear of appliance, above gas connection.

- Beside the rating plate.

Commissioning

Before leaving the installation;
1.

Check all gas connections for leakage using soapy water or other gas detecting equipment.

Carry out a ‘Commissioning’ check of the appliance as shown in Installation Section of this manual.

Ensure any adjustments done to components that have adjustments / settings paint sealed, these are to be re-sealed.

NOTE, Pin rotated

for Natural Gas

NOTE, Pin rotated

for LPG

Pressure Adjusting

Screw

Cap Nut

NOT

USE

NAKED

FLAME

CHECK

FOR

GAS

LEAKAGES

Warning

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды