Blue Seal Evolution Series Скачать руководство пользователя страница 41

Страница: 41 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

6.5.12 Indicators

Open the control panel (refer 6.1.2).

Remove wires from rear of the indicator.

Push indicator through from rear of control panel.

Replace indicator and re-assemble in reverse order.

Figure 6.5.12

6.5.11 Thermostat

Remove oven control panel (refer 6.1.2).

Remove knob from thermostat and remove two screws
securing thermostat to control panel.

Remove side panel.

Unscrew two screws holding thermostat probe.

Feed thermostat probe back through hole in side of oven.

Remove and replace, re-assemble in reverse order.

Figure 6.5.11

Remove right hand side panel from the unit.

Remove all wiring from the capacitor.

Undo nut securing capacitor to terminal block bracket.

Replace capacitor and re-assemble in reverse order.

6.5.13 Motor Capacitor

Figure 6.5.13

Capacitor

6.5.14 Microswitch

Remove the bottom lintel. (refer 6.5.1).

Open door slightly and lift door to allow removal of lintel.

Remove oven control panel (refer 6.1.2)

Remove two wires from the microswitch, noting their
positions.

Remove two screws securing microswitch to bracket and
remove microswitch.

Bend new microswitch lever arm so that it is of the same

curvature as original microswitch.

Replace and re-assemble in reverse order ensuring wires
go to the correct terminals.

Before re-fitting the control panel, ensure that the micro-
switch is clicking ‘On’ and ‘Off’ when the oven door is
opened and closed.

Figure 6.5.14b

Two Screws

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды