Blue Seal Evolution Series Скачать руководство пользователя страница 36

Страница: 36 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

6.4.8 Griddle Spark Electrode

Remove griddle and reflector plates.

Remove griddle burner for access (refer 6.4.3).

Remove H.T lead from the rear of electrode.

Unscrew electrode from pilot burner assy.

Replace and re-assemble in reverse order.

6.4.9 Griddle Burner H.T Lead

Remove control panel (refer 6.1.1).

Remove H.T. lead from rear of piezo ignitor and pilot
electrode.

Replace and re-assemble in reverse order.

6.4.10 Piezo Ignitor

Remove control panel (refer 6.1.1).

Remove HT lead from piezo ignitor by pulling HT Lead
firmly away from rear of Ignitor.

Unscrew securing nut and withdraw Piezo Ignitor from
control panel.

Replace and re-assemble in reverse order.

Figure 6.4.8

Piezo Electrode

Figure 6.4.9

Figure 6.4.10

Piezo Igniter

Securing Nut

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды