Blue Seal Evolution Series Скачать руководство пользователя страница 80

Страница: 80 / 94

Appendix A: Hob Type Conversion

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

Suitable for the following models:

All Blue Seal 800 Series Cook Tops.

Contents:

990008

Burner Module PF Hob

Qty 1.

229686

Instruction Sheet

Qty 1.

B30245

Injector 2.45mm NAT

Qty 2.

026592

Carton Burner Modules

Qty 1.

B30155

Injector 1.55mm LPG

Qty 2.

010329

Plastic Bag Self Seal

Qty 1.

B30145

Injector 1.45mm Butane

Qty 2.

Additional parts required but not supplied as part of kit:

227384

Knob Blue Seal Gas PF (Open Burner)

Qty 2.

227015

Pot Stand Blue Seal.

Qty 2.

SERVICE WORK ONLY TO BE CARRIED OUT BY QUALIFIED PERSONS

Fig 5

Front Burner Securing Screws

Cook Top Open Burners - Removal

1.  Turn ‘OFF’ gas supply at main supply.
2.  Remove pot stands from top of cook top.
3.  Remove burner caps and burner bowls from top of

burner venturi, these are a loose fit to the burner
venturi, (See Fig 1), taking care not to damage
thermocouples fitted through splash guards.

4. Remove the splash guard covering the burner

venturi’s by unscrewing the two allan headed cap
screws. (4mm) (See Fig 2).

5. Carefully remove the splash guard taking care not to

damage the thermocouples protruding through the
splash guard.

6. Remove all the gas control knobs from the front of

the control panel. These are a push fit onto the gas
control valve shaft.

7. Unscrew the securing screws and remove the front

control panel.

8. Disconnect the 2 gas valves (See Fig 3) from the gas

manifold.

9. Unscrew the 2 securing screws at the rear (See Fig

4) and 2 screws at the front of the cook top open
burner module, (See Fig 5) and carefully remove the
burner module from the cook top.

Fig 1

Burner Cap

Burner

Bowl

Fig 2

Cap Screws

Splash Guard

Fig 3

Gas Valve

Connections

Gas Manifold Spigots

Rear Burner

Securing Screws

Fig 4

228790 COOK TOP BURNER– PF MODULE KIT

CAUTION:

ENSURE THE APPLIANCE IS ISOLATED FROM GAS AND ELECTRICAL SUPPLIES BEFORE COMMENCING SERVICING.

CHECK THE APPLIANCE FOR GAS LEAKS AT COMPLETION OF SERVICING.

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды