Blue Seal Evolution Series Скачать руководство пользователя страница 35

Страница: 35 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

6.4.5 Griddle Pilot Burner

Remove griddle plate.

Remove griddle reflector.

Remove griddle burner (refer 6.4.3).

Unscrew pilot supply tube, piezo electrode, and
thermocouple from pilot assembly.

Undo two screws securing pilot burner bracket to griddle
reflector.

Remove pilot burner from bracket (two screws).

Replace and re-assemble in reverse order.

NOTE: Ensure thermocouple is positioned correctly in

holder before tightening.

6.4.6 Griddle Pilot Burner Injector

Remove griddle plate and reflector plate.

Remove griddle burner (refer 6.4.3).

Unscrew pilot supply tube from pilot burner assembly.

Remove injector from pilot burner.

Clean or replace as necessary, and re-assemble in
reverse order.

Figure 6.4.5

Figure 6.4.6

Two Screws

Pilot Burner

Thermocouple

Pilot Supply

Piezo Electrode

Pilot Supply Tube

6.4.7 Griddle

Thermocouple

Remove griddle and reflector plates.

Remove griddle burner for access (refer 6.4.3).

Unscrew pilot thermocouple from pilot burner assembly.

Undo thermocouple from griddle gas control.

Replace and re-assemble in reverse order.

NOTE: When re-fitting thermocouple back into gas

control valve, once threaded up, tighten another
¼ turn only. Do not over-tighten.

Figure 6.4.7b

Thermocouple to

Gas Control

Valve Connection

Figure 6.4.7a

Thermocouple

Содержание Evolution Series































































































Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды

Blue Seal Evolution Series, Руководство по обслуживанию

Результаты поиска

Содержание Evolution Series

Отзывы:

Похожие инструкции для Evolution Series

Бренды по названию

Популярные бренды