background image

 

 

IM0001_L2_R_WMv1.3  

3

 

Federal Communications Commission (FCC) Statement 

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy, and if not installed and used in accordance with these 
instructions, may cause harmful interference to radio communications. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 

 

Reorient or relocate the antenna. 

 

Increase the separation between the equipment and the receiver. 

 

Connect the equipment to an outlet on a circuit different from that to which the receiver is 
connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 

1.

 

This device may not cause harmful interference, and 

2.

 

This device must accept any interference received, including interference that may cause 
undesired operation. 

 

Содержание Wall Mount Charging System






























Отзывы: