5
3. Safety
Warning!
Read all safety warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire, explosions and / or serious injuries.
Only authorized and trained personnel may operate this machine. This machine is not
intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge. Always use common sense when working
with machines.
It is the responsibility of the user to analyse the surface to be treated. The surface may not contain any
substances which could pose a fire-, explosion- or health risk when treated. The user should make a risk
assessment on the basis of the information obtained about the surface to be treated and take proper
precautions for the work to be performed.
In case of any inappropriate usage, improper operation or repair, the producer shall be exempt from liability.
3.1
Work area safety
a)
Do not use the machine in rain, damp or wet locations.
b)
Avoid dangerous environments: do not use in the presence of explosive atmospheres, in the presence
of flammable liquids, vapours, gases or dust. Remove materials / debris that may be ignited by sparks.
c)
In some cases
sparks
could be created by the blast cleaning process.
d)
Keep the work area clean and make sure there is enough ambient light on the work area.
Cluttered or dark areas invite accidents.
e)
Do not use on wood.
f)
Keep children and bystanders away while operating the machine. They are likely not to foresee the
potential dangers of the machine. Distractions could cause you to lose control of the machine.
g)
Persons who are not operating the machine must not be permitted to stay in the surrounding area of
at least 15 meter from the machine.
h)
Never use the machine when the workfloor is not clear and if there is a risk of stumbling or tripping.
i)
Make sure the machine can travel over all inequalities on the surface, small inequalities like weld
seams or joints are no barriers for the machine.
j)
Never operate the machine when workplace is wet. Never stay in the rain with the machine.
k)
Check if there are any obstacles that can snag the cables or dust hose when the machine is moving.
l)
Warning!
Make sure that the surface to be treated does not contain dangerous materials
such as:
- combustible or explosive dusts or substances.
- carcinogenic or pathogenic substances.
m)
It is necessary to provide for an adequate air change rate L in the room if the exhaust air from the
dust collector is returned to the room. Comply with the National regulations.
n)
Secure the work area around the machine in public areas providing an adequate safety distance from
the machine. Use a red and white safety chain and danger sign to enclose the work area.`
o)
The operator must always be at a safe distance, straight behind the machine with the most optimal
view on the machine and working environment.
p)
Never stand directly below the machine.
3.2
Electrical safety
a)
Use only extension cables for extending the main cable that are sized and marked in accordance with the
overall power consumption of the machine. Do not use damaged extension cables.
b)
Electrical cables must be rolled entirely off of the reels.
c)
Any damage to the electric cables and/or electrical components is not permitted.
d)
If the power supply cable or plug is damaged, it must be replaced immediately. Only use original Blastrac
parts.
e)
The voltage on the identification plate must comply with the power supply.
f)
Use an electrical power supply connection with earth connection and earth leakage circuit breaker.
g)
The circuit breaker of the power su
pply must have a ‘’D’’ characteristic. Circuit breakers with a “C” or “B”
characteristic can give problems when switching the machine on.
h)
Keep the machine original; The machine is always equipped with an earthed connection, do not
change this
and always use earthed cables with an earthed plug.
i)
Inspect and test the electrical components regularly. The electrical components have to satisfy with the
requirements set out in the harmonised norm EN60204-1.
Содержание 200VMB
Страница 1: ...Original instructions in English OPERATING INSTRUCTIONS 200VMB VERSION 1 2...
Страница 22: ...22 2 Use a brass drift to tap out the side liners...
Страница 23: ...23...
