Birmingham WSG1640AHD Скачать руководство пользователя страница 29

Страница: 29 / 85

Operating Manual

4) Check the spindle rotating and make sure the direction is clockwise.

Before check the spindle rotating direction, please remove the wheel,

because the spindle turning unticlockwisly is very dangerous.

5) Conform the oil tank is full enough.

6) Make sure the speed control valve is taken off.

7) Adjusting suitable travel by adjusting the position of these two “travel

adjusting block”

8) Check if all the fixed blocks have been took out.

9) When working the wheel cover should be never opened.

10) Check the pipes connected to the oil tank.

11) All above items have been checked , then look around and to find if there

is any other person in the working area, let him go to prevent from

danger.

12) The machine operating will be explained in next chapter.

13) Remember the position of the EMERGENCY SWITCH

Содержание WSG1640AHD






















































































Результаты поиска

Содержание WSG1640AHD

Отзывы:

Похожие инструкции для WSG1640AHD

Бренды по названию

Популярные бренды

Birmingham WSG1640AHD, Руководство по эксплуатации

Результаты поиска

Содержание WSG1640AHD

Отзывы:

Похожие инструкции для WSG1640AHD

Бренды по названию

Популярные бренды