Biolase Waterlase iPlus Скачать руководство пользователя страница 23

Страница: 23 / 82

Installation

Waterlase iPlus User Manual

INSTALLATION INSTRUCTIONS

The Waterlase iPlus laser system must be installed by a qualified BIOLASE employee or representative

who will unpack and install the laser. Please leave all crates and shipping containers unopened until

the

trained

representative

arrives.

Complete

installation,

testing,

and

demonstration

require

approximately one full day.

Please contact the representative before transporting the laser system to a different location.

Misalignment of optical components may occur during transportation if the laser is not properly packaged.

FACILITY REQUIREMENTS

ELECTRICAL SUPPLY:

100 VAC

15.0 Amps to 230 VAC

8.0 Amps, 50/60 Hz

NOTE:

The main power supply of the iPlus laser system has an

isolation transformer that complies with a Transient Voltage of 4kV.

COMPRESSED AIR SUPPLY:

80 - 120 psi (5.5 - 8.2 bar)

ENVIRONMENTAL REQUIREMENTS

TEMPERATURE:

15 - 30 °C

HUMIDITY:

20% - 80%, non-condensing

AIR SUPPLY:

Connections for an air supply must be available in each operatory. Attach an air hose

with 1/4” inside diameter male quick connectors on each end between the air inlet connector and the

operatory air source.

CAUTION:

Prior to connection, verify that the outlet is for the

air, NOT the water supply.

Connection to the water supply may

cause damage to the Waterlase iPlus system. If the laser console

is connected to the water supply, DO NOT turn the system on;

contact the service representative.

WARNING:

To avoid the risk of electric shock, this equipment must

only be connected to a supply mains with protective earth.

CAUTION:

Moisture in the air supply line may damage the laser

system. Please provide proper filtration to eliminate all moisture

from the air source.

CAUTION

DO NOT position this equipment so that it is difficult to

pull the plug from the power source.

Содержание Waterlase iPlus



















































































Результаты поиска

Содержание Waterlase iPlus

Отзывы:

Похожие инструкции для Waterlase iPlus

Бренды по названию

Популярные бренды

Biolase Waterlase iPlus, Руководство пользователя

Результаты поиска

Содержание Waterlase iPlus

Отзывы:

Похожие инструкции для Waterlase iPlus

Бренды по названию

Популярные бренды