Big Joe PDSR 30 Скачать руководство пользователя | Manualshive

Страница: 69 / 172

background image

BL-PDSR 30-0319 - 03-07-2019

10-1

SECTION 10

ELECTRICAL COMPONENTS

10-1. ELECTRICAL CONTROL PANEL

10-1.1. Maintenance

NOTE:

Erratic operation of the truck may be caused

by defective controller components. Before
removing the electrical panel, perform
troubleshooting procedures per Section

,

to determine corrective action to be

taken.

There are no user-serviceable parts inside the control-
ler. No attempt should be made to open the control-
ler. Opening the controller may damage it and will void
the warranty.

The controller is programmed at the factory specifi-
cally for the truck model on which it is equipped. It is
important to replace the controller with the correct
preprogrammed unit to assure proper performance
settings intended for that particular truck. See

for the preprogrammed controller number.

It is recommended that the controller exterior be
cleaned periodically, and if a hand held programmer is
available, this periodic cleaning provides a good
opportunity to check the controller ’s diagnostic
history file

.

It is also recommended that the con-

troller

’s fault detection circuitry be checked

whenever the vehicle is serviced.

10-1.2. Cleaning

1.

Engage the emergency stop switch and turn off
key switch.

2.

Remove the compartment covers as described
in paragraph

.

3.

Remove any dirt or corrosion from the bus bar
area. The controller should be wiped clean with a
moist rag. Allow it to dry before reconnecting the
battery.

4.

Make sure the connections to the buss bars are
tight.Use two well insulated wrenches for this task
in order to avoid steering the buss bars.

10-1.3. Panel Removal

1.

Engage the emergency stop switchand turn off
key switch.

2.

Remove the compartment covers as described
in paragraph

.

3.

Tag and disconnect all electrical cables which
connect to the control panel.

4.

Remove four screws, four lock washers, four
flat washers and control panel.

10-1.4.

Panel Disassembly

Refer to

for location and identity of the

major replacement components mounted on the
panel and remove defective parts.

NOTE:

Contactor (2or17) is not repairable and must

be replaced if defective.

10-1.5.

Panel Installation

1.

Install the control panel and secure with four
screws, four lock washers and four flat washers.

2.

Connect all electrical cables to the control panel
as noted during removal.

3.

Install the compartment covers as described in
paragraph

.

4.

Disengage the emergency stop switch and turn on
key switch.

10-2.

HORN REPLACEMENT

1.

Engage the emergency stop switch and turn off
key switch.

2.

Remove the compartment covers as described
in paragraph

.

3.

Tag and disconnect all electrical connections from
horn.

4.

Remove screw, lock washer, flat washer and
horn.

5.

Install new horn and secure with screw, lock
washer, flat washer.

6.

Install the compartment covers as described in
paragraph

.

7.

Disengage the emergency stop switch and turn on
key switch.

«
...
67
68
69
70
71
...
»

Содержание PDSR 30













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PDSR 30

Бренд: Landoll Страницы: 35

Бренд: AMOG Страницы: 112

Бренд: GMR Страницы: 26

Бренд: Parker Страницы: 12

Бренд: Parker Страницы: 14

Бренд: Dodge Страницы: 268

Бренд: U-Line Страницы: 6

Бренд: Eagle Group Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды