Big Joe PDSR 30 Скачать руководство пользователя | Manualshive

Страница: 56 / 172

background image

9-6

BL-PDSR 30-0319 - 03-07-2019

9-2. HYDRAULIC PUMP, MOTOR AND RESERVOIR

The hydraulic pump/motor assembly can be disas-
sembled and repaired. However, a defective pump,
valve or motor requires replacement of that compo-
nent.

WARNING:

When forks are raised

,

pressure exists in

the hydraulic system lines and fittings

.

To

ensure release of pressure

,

forks must

be fully lowered and the batteries discon-
nected before performing any mainte-
nance on the hydraulic system.

9-2.1. Removal

1.

Lower forks fully.

2.

Engage the emergency stop switch and turn off
key switch.

3.

Remove the compartment covers as described in
paragraph

.

NOTE:

The reservoir and hose will be filled with

hydraulic oil. Place a container under the
pump assembly to catch any hydraulic oil.

4.

Tag and disconnect electrical leads from motor
and solenoid. Refer to

.

5.

Disconnect hoses from pump/motor assembly.

6.

While supporting the pump/motor assembly,
remove four screws and four lock washers.

7.

Remove the pump/motor assembly.

9-2.2. Disassembly and Reassembly

1.

Remove the hydraulic pump/motor assembly as
described in paragraph

2.

Refer to

for disassembly and reas-

sembly.

9-2.3. Installation

1.

While supporting the pump/motor assembly,
secure with four screws and four lock washers.

2.

Reonnect hoses to pump/motor assembly.

3.

Connect electrical leads to motor and solenoid.
Refer to

and

..

.

4.

Fill the hydraulic reservoir. Use hydraulic oil listed
in

.

5.

Disengage the emergency stop switch and turn
on key switch.

6.

Operate the lift and lower buttons to refill the
cylinder and lines with hydraulic oil.

7.

Check level of hydraulic oil. If required, add
hydraulic oil to bring to proper level. Use
hydraulic oil listed in

.

8.

Install the compartment covers as described in
paragraph 5-2

Figure 9-3 Hydraulic System

DR_0008

«
...
54
55
56
57
58
...
»

Содержание PDSR 30













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PDSR 30

Aeromaster 1997

Бренд: Utilimaster Страницы: 56

EQ1040GLJ4-CMD1-D

Бренд: DongFeng Страницы: 75

Бренд: Navistar Страницы: 84

Dennis Eagle Olympus

Бренд: RosRoca Страницы: 104

COLUMBUS McKINNON 040016431

Бренд: Pfaff Страницы: 24

Бренд: LOAD KING Страницы: 18

LEGACY 3 Series

Бренд: LOADMASTER Страницы: 25

Бренд: Einhell Global Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды