Big Joe PDSR 30 Скачать руководство пользователя

Страница: 26 / 172

4-8

BL-PDSR 30-0319 - 03-07-2019

EV2 DRIVER

SHORTED

Electro valve EV2 driver is shorted

Check if there is a short or a low imped-

ance between the negative of this coil

and -BAT. This warning also occurs if

the external load is not present and the

parameter EV2 in the “Set Options”

menu is set “PRESENT”, in this case

the warning disappears setting the EV2

parameter “ADBSENT”. Otherwise the

driver circuit is damaged

and the controller must be replaced.

EV3 DRIVER

SHORTED

Electro valve EV3 driver is shorted

Check if there is a short or a low imped-

ance between the negative of this coil

and -BAT. This warning also occurs if

the external load is not present and the

parameter EV3 in the “Set Options”

menu is set “PRESENT”, in this case

the warning disappears setting the EV3

parameter “ADBSENT”. Otherwise the

driver circuit is damaged

and the controller must be replaced.

PUMP I NO ZERO

In standby condition (pump motor not

driven), the feedback coming from the

current sensor in the pump chopper

gives a value out of a permitted range.

This type of fault is not related to exter-

nal components; replace the controller

PUMP I=0 EVER

This test is carried out when the pump

motor is running, and it verifies that the

current feedback sensor is not con-

stantly

stuck to

• Check the motor connection, that

there is continuity. If the motor connec-

tion is opened, the current cannot flow,

so the test fails and the error code is

displayed.

•

If everything is ok for what it concerns

the motor

the problem could be in the

current sensor or in the related circuit.

CONT

DRV

EV1

The EV1 valve driver is not able to drive

the load (cannot close).

The device or its driving circuit is dam-

aged, replace the controller

CONT

DRV

EV2

The EV2 valve driver is not able to drive

the load (cannot close).

The device or its driving circuit is dam-

aged, replace the controller

CONT

DRV

EV3

The EV3 valve driver is not able to drive

the load (cannot close).

The device or its driving circuit is dam-

aged, replace the controller

PUMP VACC NOT

The minimum of the lift potentiometer is

not correctly set.

It is suggested to repeat a “PROGRAM

VACC” procedure

SENS. MOT. TEMP

• The motor temperature sensor is not

correctly connected to A22.

•

The motor temperature sensor is

damaged.

• Check the correct connection of the

motor temperature sensor.

• If the current sensor is correctly con-

nected, replace it.

•

If the problem persist, replace the

controller

VACC OUT RANGE

The voltage on CNC#4 is outside of the

parameters’ range.

Please re-acquire the VACC parame-

ters with a PROGRAM VACC proce-

dure.

Error Message

Possible Cause

Fault Elimination

Code

Error Text

Содержание PDSR 30













































































































































































Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды

Big Joe PDSR 30, Установка, эксплуатация, техническое обслуживание и запасные части

Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды