Big Joe PDSR 30 Скачать руководство пользователя | Manualshive

Страница: 46 / 172

background image

8-2

BL-PDSR 30-0319 - 03-07-2019

8-3. LIFT CHAIN WEAR INSPECTION

Both lift chains should be replaced when either chain
is worn enough to increase it’s length by 3% or more.
To make this determination proceed as follows.

Using a section of chain that sees the most frequent
operation over the chain sheaves, isolate a vertical
portion under tension from the weight of carriage and
forks.

Measure the distance between pin centers on 20
vertical links. If the section measures 12.88” or more,
the chain should be replaced.

New chain anchor, clevis pins and cotter pins should
be installed when chains are replaced

.

Never replace a

partial section of chain and never repair chain. Refer
to paragraph 8-4. when installing new chain.

8-4. LIFT CHAIN REPLACEMENT

8-4.1. Telescopic

1.

With the lift truck wheels securely blocked, raise
the forks approximately three feet from floor and
position blocks or strong supports under inner
mast.

2.

Lower inner mast onto the support. Check that
arrangement is secure before proceeding.

WARNING:

Before attempting any adjustment, make
certain power is disconnected.

3.

Engage the emergency stop switch and turn off
key switch.

4.

Remove cotter pin and clevis pin connecting
chain to chain anchor at the lift carriage.

5.

Remove cotter pin and clevis pin connecting
chain to chain anchor at the outer mast.

6.

Remove chain from sheave.

7.

Position new chain on sheave.

8.

Secure new chain to new chain anchor at the
outer mast with new clevis pin and new cotter
pin.

9.

Connect the opposite end of new chain to new
chain anchor at the lift carriage with new clevis
pin and new cotter pin.

10.

Adjust the chains according to paragraph 8-2.

11. Disengage the emergency stop switch (and turn

on key switch.

«
...
44
45
46
47
48
...
»

Содержание PDSR 30













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PDSR 30

Бренд: Komatsu Страницы: 258

Бренд: Komatsu Страницы: 446

Бренд: DAF Страницы: 18

Бренд: Jacobsen Страницы: 24

1500 CLASSIC 2022

Бренд: RAM Страницы: 364

Бренд: Jungheinrich Страницы: 49

Бренд: Conrad Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды