Big Joe PDSR 30 Скачать руководство пользователя

Страница: 60 / 172

9-10

BL-PDSR 30-0319 - 03-07-2019

9-2.6.3. Installation

Using another lift truck or suitable jack, raise mid-
dle mast far enough to allow installation of the
secondary lift cylinder.

Slowly lower mast while aligning cylinder with the
top on mast.

Secure the top of cylinder with flat washer, lock
washer and screw.

Install clamp, support, two flat washers, two lock
washers and two bolts.

Reconnect the tube to the bottom of the lift cylin-
der.

Fill the hydraulic reservoir. Use hydraulic oil listed
in

Table 3-2

Disengage the emergency stop switch (and turn on
key switch.

Operate the lift and lower buttons to refill the cyl-
inder and lines with hydraulic oil.

Check level of hydraulic oil. If required, add
hydraulic oil to bring to proper level. Use hydraulic
oil listed in

Table 3-2

10.

Install the compartment covers as described in
paragraph

5-2.

9-2.7. Reach Cylinder

9-2.7.1. Removal

Fully lower the lift carriage.

Engage the emergency stop switch and turn off
key switch.

WARNING:

Before attempting any replacement,
make certain power is disconnected.

CAUTION:

Hydraulic oil can damage parts. Wipe off
any oil immediately. Provide a container
under the line or fitting before discon-
necting.

Disconnect the hose from the reach cylinder.

WARNING:

Support reach cylinder before perform-
ing the following steps to prevent cylinder
from falling.

Remove screw, shaft from the scissors base.

Remove screw, shaft from the scissors.

Remove cylinder and out of truck.

Figure 9-7 Reach Cylinder

9-2.7.2. Repair

CAUTION:

To prevent damage, use proper pipe

clamp vise. The cylinder will be distorted
if the vise is tightened too much.

Secure the cylinder in a vise, clamping lightly at
the base of the cylinder.

Remove connector, lock washer

and round nut

from piston rod.

Remove gland nut.

Remove wiper ring, O-ring, seal and

O-ring from

gland nut.

Pull out piston rod.

Remove guide ring and seal from piston rod.

Coat all parts with hydraulic oil (

Table 3-2

Install guide ring and new seal on piston rod.

Insert rod in cylinder tube.

10.

Install wiper ring, O-ring, seal and

O-ring on

gland nut.

11.

Install gland nut in cylinder tube.

12. Install connector, lock washer and round nut from

piston rod.

DR_0018

Содержание PDSR 30













































































































































































Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды

Big Joe PDSR 30, Установка, эксплуатация, техническое обслуживание и запасные части

Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды