Big Joe PDSR 30 Скачать руководство пользователя

Страница: 24 / 172

4-6

BL-PDSR 30-0319 - 03-07-2019

TH. PROTECTION

This alarm occurs when the tempera-

ture of the base plate is higher than

85°C. Then the maximum current

decreases proportionally with the tem-

perature increases from

85°C to 105°C. At 105°C the

Current is limited to

Amps.

Improve the air cooling of the controller.If

the alarm is signaled when the control-

ler is cold, the possible reasons are a

thermal sensor failure or a failure in the

logic card. In this case, it is necessary

to replace the controller

BATTERY LOW

This occurs when the battery charge is

calculated being less than or equal to

10% of the full charge and the BAT-

TERY CHECK setting is other than 0

(refer to SET OPTION menu).

Charge the battery.If charging does not

help, using a voltmeter

measure the bat-

tery volt- age and compare the reading

with the value in the BATTERY VOLT-

AGE parameter

If they are different,

adjust the value of the ADJUST BAT-

TERY function.

EEPROM KO

This is due to a HW or SW defect of the

non-volatile embedded memory sup-

porting the controller parameters. This

alarm does not inhibit the machine

operations, but the truck will work with

the default values.

Try to execute a CLEAR EEPROM

operation (refer to CONSOLE manual).

Switch the key off and on to check the

result. If the alarm occurs permanently

it is necessary to replace the controller

If the alarm disappears, the previously

stored parameters will have been

replaced by the default parameters.with

the temperature increases from 85°C to

105°C.

MOTOR

TEMPERATURE

This warning occurs when the tempera-

ture sensor is opened (If digital) or has

overtaken the threshold of 150°C

(if analog).

Check the thermal sensor inside the

motor (use the MOTOR TEMPERA-

TURE reading in the TESTER menu);

check the sensor ohmic value and sen-

sor wiring. If the sensor is OK, improve

the air cooling of the motor

If the warn-

ing is present when the motor is cool,

then the problem is inside the controller

THERMIC

SENSOR KO

The output of the controller thermal

sensor is out of range.

This type of fault is not related to exter-

nal components; replace the controller

CHECK UP

NEEDED

This is just a warning to call for the time

programmed maintenance.

It is just enough to turn the CHECK UP

DONE option to level ON after the

maintenance is executed.

DATA

ACQUISITION

Acquisition of the current gains.

The alarm ends when the acquisition is

done.

Error Message

Possible Cause

Fault Elimination

Code

Error Text

Содержание PDSR 30













































































































































































Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды

Big Joe PDSR 30, Установка, эксплуатация, техническое обслуживание и запасные части

Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды