Big Joe PDSR 30 Скачать руководство пользователя

Страница: 23 / 172

BL-PDSR 30-0319 - 03-07-2019

4-5

4-2.4 Settings and Adjustments

4-2.4.1 Set Options

To set options proceed as follows and refer to

Table 4-2:

Connect the Zapi Handset, refer to paragraph
4-2.1.

Press the ROLL up button and the SET up button
(5) at the same time to enter the CONFIG MENU.

Press the ROLL down button or the ROLL up but-
ton to find the SET OPTIONS display

Press the ENTER button to view the options.

Press the ROLL down or the ROLL up button to
find the option to be changed.

Press the SET up button or the SET down but- ton
(6) until the desired value setting is reached. The
option is now set at the desired value.

Press the OUT button to exit the options.

Table 4-2Traction Controller

Error Message

Possible Cause

Fault Elimination

Code

Error Text

SLIP PROFILE

This is an error on the choice of the

parameters of the slip pro- file.

So ask for the assistance of a Zapi

technicians when this alarm

FORW+BACK

This alarm occurs when both the travel

(Fwd and Rev) are active at the same

time.

Check the wiring of the Fwd and Rev

travel demand inputs (use the readings

in the TESTER to facilitate the trouble-

shooting). Check the micro switches for

failures.

A failure in the logic is possible too

when you have verified the travel

demand switches and wiring are cor-

rect

it is necessary to replace the con-

troller

INCORRECT

START

This is a warning for an incorrect start-

ing sequence.

The possible reasons for this alarm are

(use the readings in the TESTER to

facilitate the troubleshooting):

• A travel demand was active at key-on.

• Presence man sensor was active at

key- on.

Check the wiring. Check the micro-

switches. It could also be an error

sequence made by the operator. A fail-

ure in the logic is possible too; so when

all of the above are checked and noth-

ing was

found, replace the controller

VACC NOT OK

The test is made at key-on and after 20

sec that both the travel demands have

been turned off. This alarm occurs if the

ACCELERATOR reading in the TES-

TER menu is 1.0V higher than PRO-

GRAM VACC min acquisition when the

accelerator is released.

Check the mechanical calibration and

the functionality of the potentiometer

Содержание PDSR 30













































































































































































Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды

Big Joe PDSR 30, Установка, эксплуатация, техническое обслуживание и запасные части

Результаты поиска

Содержание PDSR 30

Отзывы:

Похожие инструкции для PDSR 30

Бренды по названию

Популярные бренды