BFT SHYRA AC BA Скачать руководство пользователя страница 21

Страница: 21 / 40

ENGLISH

INSTALLATION MANUAL

1) GENERAL INFORMATION

The SHYRA AC SL / SHYRA AC BA control panel comes with standard factory

settings.

Any change must be set by means of the TRIMMER and DIP SWITCH settings.

Its main features are:

- Control of 1 single-phase motor

- Separate inputs for safety devices

- Built-in radio receiver rolling code with transmitter cloning.

The board has a terminal strip of the removable kind to make maintenance or re-

placement easier. It comes with a series of prewired jumpers to make the installer’s

job on site easier. The jumpers concern terminals: 70-71, 70-72, 70-74. If the

above-mentioned terminals are being used, remove the relevant jumpers.

TESTING

The SHYRA AC SL / SHYRA AC BA panel controls (checks) the start relays and

safety devices (photocells) before performing each opening and closing cycle.

If there is a malfunction, make sure that the connected devices are working

properly and check the wiring.

2) TECHNICAL SPECIFICATIONS

Power supply

120V 60Hz (SHYRA AC SL / SHYRA AC BA 120V)
220-230V 50/60 Hz (SHYRA AC SL / SHYRA

AC BA 230V)

Panel dimensions

Fig. F

Low voltage/mains insulation

> 2MOhm 500V

Operating temperature range

-20 / +55°C

Dielectric rigidity

mains/LV 3750V~ for 1 minute

Accessories power supply

4V~ (demand max. 0,2A)

AUX 0 - Flashing

Contact powered

120V~ 40W max

(SHYRA AC SL / SHYRA AC

BA 120V)
230V~ 40W max

(SHYRA AC SL / SHYRA AC

BA 230V)

Fuses

Fig. C

Built-in Rolling-Code

radio-receiver

frequency 433.92MHz

Setting of parameters and logics T DIP SWITCH
N° of combinations

4 billion

Max. n° of remotes that can be

memorized

Pedestrian work time

8 s.

Maximum power

500W

Maximum work time

120s - SHYRA AC SL

10s - SHYRA AC BA

Usable transmitter versions:

All ROLLING CODE transmitters compatible with

3) TUBE ARRANGEMENT Fig. A

Install the electrical system referring to the standards in force for electrical systems

CEI 64-8, IEC 364, harmonization document HD 384 and other national standards.

4) TERMINAL BOARD WIRING Fig. C

For the electric diagram and the cross section of the cables refer to the

manual of the actuator.

Once suitable electric cables have been run through the raceways and the auto-

mated device’s various components have been fastened at the predetermined

points, the next step is to connect them as directed and illustrated in the diagrams

contained in the relevant instruction manuals. Connect the live, neutral and earth

wire (compulsory).

WARNINGS - When performing wiring and installation, refer to the standards

in force and, whatever the case, apply good practice principles. Wires carrying

different voltages must be kept physically separate from each other, or they must

be suitably insulated with at least 1mm of additional insulation.

Wires must be secured with additional fastening near the terminals, using devi-

ces such as cable clamps. All connecting cables must be kept far enough away

from dissipaters.

WARNING! For connection to the mains power supply, use a multicore cable

with a cross-sectional area of at least 3x1.5mm

of the kind provided for by

the regulations in force.

To connect the motors, use a cable with a cross-sectional area of at least

1.5mm

of the kind provided for by the regulations in force.

The cable must be type H05RN-F at least.

5) SAFETY DEVICES

Note: only use receiving safety devices with free changeover contact.

5.1) TESTED DEVICES Fig.G

5.2) CONNECTION OF 1 PAIR OF NON-TESTED PHOTOCELLS FIG. B

WARNING!

The values of the impact force according to EN 12453 are only observed with

the use of safety edges (active) connected to the board.

6) MEMORIZING TRANSMITTERS FIG. D

RADIO

- IMPORTANT NOTE: THE FIRST TRANSMITTER MEMORIZED MUST BE

IDENTIFIED BY ATTACHING THE KEY LABEL (MASTER).

In the event of manual programming, the first transmitter assigns the RECEIVER’S

KEY CODE: this code is required to subsequently clone the radio transmitters.

The Clonix built-in on-board receiver also has a number of important advanced features:

• Cloning of master transmitter (rolling code or fixed code).

• Cloning to replace transmitters already entered in receiver.

• Transmitter database management.

• Receiver community management.

To use these advanced features, refer to the universal handheld programmer’s

instructions and to the general receiver programming guide.

7) REVERSING THE OPENING DIRECTION (Fig.E)

8) ADJUSTMENT PROCEDURE

- Before turning the unit on, check electrical connections.

- Set the following parameters:

Automatic Closing Time,

Work Time (for SHYRA AC SL only).

- Set the logics.

WARNING! Incorrect settings can result in damage to property and injury

to people and animals.

WARNING: Check that the force of impact measured at the points pro-

vided for by standard EN 12445 is lower than the value laid down by

standard EN 12453.

KEYS

Description

Add Start Key

associates the desired key with the Start command.

Add Pedestrian Key (SHYRA AC SL)

associates the desired key with the pedestrian command.

Add Open key (SHYRA AC BA)

associates the desired key with the open command.

>5s

Confirms the changes made to parameter settings and operating

S1+S2

>10s

Erase List

WARNING! Erases all memorized transmitters from the

receiver’s memory.

LED INDICATORS:

POWER Steadily lit: - Mains power on - Board powered - Fuses intact

START

Lit: START input activated

OPEN

Lit: OPEN pedestrian input activated

STOP

Unlit: STOP input activated

PHOT

Unlit: PHOT photocell input activated

FAULT 1 PHOT input safety device test input diagnostics

BAR

Unlit: BAR safety edge input activated

FAULT 2 BAR input safety device test input diagnostics

SWC

Unlit: leaf fully closed
Lit: motor limit switch is disengaged
Flashing: end of the work time while closing

SWO

Unlit: leaf fully open
Lit: motor limit switch is disengaged
Flashing: end of the work time while opening

ERR

Unlit: no error
LIT: see error diagnostics table

RADIO

(GREEN)

Unlit: remote programming not active

Radio LED only flashing: Remote programming active, waiting for

hidden key.

Flashing in sync with Set LED: Transmitter deletion in progress
Lit: remote programming active, waiting for desired key.
Lit 1s: Radio receiver channel activated

SET

Lit: see error diagnostics table
Flashing in sync with Radio LED: Transmitter deletion in progress

SHYRA

D812090 00100_04

Содержание SHYRA AC BA









































Результаты поиска

Содержание SHYRA AC BA

Отзывы:

Похожие инструкции для SHYRA AC BA

Бренды по названию

Популярные бренды

BFT SHYRA AC BA, Руководство по установке

Результаты поиска

Содержание SHYRA AC BA

Отзывы:

Похожие инструкции для SHYRA AC BA

Бренды по названию

Популярные бренды