Berthold Duo Xpert Скачать руководство пользователя страница 167

Страница: 167 / 233

LB 470 Level

9 Troubleshooting

56925BA2 Rev. 03, 11/2017

167

9.2.3

105B

Detector

Code

Message

NAMUR107 Help Text

D501

Detector not found

Lost connection to at least one detector.
Check detector settings and connections.
It is recommend to have the device

checked by Berthold Service, even if it
seems to work normally.

D502

Detector comm. error

Temporarily lost connection to at least
one detector. Check detector settings
and connections. Contact Berthold ser-

vice, if this event occurs repeatedly.

D503

Detector failure

At least one detector register Failure".
Check detector events.

D504

Detector out of spec.

At least one detector register "out of
specification". Check detector events.

D505

Detector function check

At least one detector register "function

check". Check detector events.

D506

Detector maintenance

At least one detector register "mainte-
nance". Check detector events.

D599

Internal program error

Internal system failure. Powercycle de-
vice. If the event remains it could be

caused by a defective hardware. Contact
Berthold service.

9.2.4

106B

RS 458 Interface

Code

Message

NAMUR107 Help Text

M699

Internal program error

Internal software failure. Restart the de-
vice. Contact Berthold service, if this
event occurs repeatedly.

9.2.5

107B

Process Connection

Code

Message

NAMUR107 Help Text

M701

Current output

Deviation of analog output value from
feeback value is too high. Calibrate ana-
log output. Contact Berthold service, if

this event occurs repeatedly.

M702

Current loop open

Current output loop open. Check cable
connection.

Содержание Duo Xpert










































































































































































































































Результаты поиска

Содержание Duo Xpert

Отзывы:

Бренды по названию

Популярные бренды

Berthold Duo Xpert, Руководство по эксплуатации

Результаты поиска

Содержание Duo Xpert

Отзывы:

Бренды по названию

Популярные бренды