Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 7

Страница: 7 / 39

Technical Documentation

Rev. 01

Power Factor Regulator

BLR-Q(U)

Page 7 of 39

1.5 Alarm relay

BLR-Q(U) is equipped with an alarm relay to signal proper function of the system. The alarm relay has one

C/O contact. The common point is terminal M.

Between the terminals M and MO is the breaking contact. This contact is closed in alarm condition or when

BLR-Q(U) is disconnected from voltage.

Between the terminals M and MS is the closing contact. This is closed in proper condition of the system.

The breaking capacity is 3A / 250V AC.

The circuit diagram is in chapter 3.4!

1.6 Digital input

1.6.1 Digital input for alarm-system

BLR-Q(U) is equipped with a digital input for AC-voltage for alarm-system (50-250V AC, terminals DI1.1 and

DI1.2). Digital input can be active high or active low. The function can be programmed in the menu "SETUP /

ALARM / DI INPUT" (2.4.25)

Following codes are possible in voltage control mode:

= control following to the charachteristic

= centre cos phi

= cos phi ind

= cos phi cap

More details for the programming can be found in chapter "ALARM".

See circuit diagram in chapter 3.4!

1.7 Digital output

BLR-Q(U) is equipped with one digital output (terminals DO1 and DO2). This output is a potential-free clos-

ing contact. The breaking capacity is 5A / 250V AC. The function of this output can be programmed in the

menu "SETUP / ALARM" (chapter 2.4.25).

The circuit diagram is in chapter 3.4!

Содержание BLR-Q(U) I/O








































Результаты поиска

Содержание BLR-Q(U) I/O

Отзывы:

Бренды по названию

Популярные бренды

Beluk BLR-Q(U) I/O, Справочное руководство

Результаты поиска

Содержание BLR-Q(U) I/O

Отзывы:

Бренды по названию

Популярные бренды