manualshive.com logo in svg

Beluk BLR-Q(U) I/O, Справочное руководство

Поделиться
Скачать
Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 11

Technical Documentation 

 

    Rev. 01 

 
Power Factor Regulator 

BLR-Q(U)

 

 

Page 11 of 39 

 

2.3.2  SWITCH CYCLES 

BLR-Q(U) is counting and showing the switching cycles of each step. This value allows the conclusion about 

the actual state of the contactors. Switch cycles can  be preset separately for each step in  SETUP/STEPS 

(2.4.22.3).  Switch  cycles  of  all  steps  is  also  reset,  by  a  reset  of  complete  capacitor  database  in 

SETUP/RESET (2.4.28.3).  

2.3.3  STEPVALUE 

As standard, the STEPVALUES are detected automatically during operation. They are rated to the setting of 

nominal  voltage.  In  some  special  applications,  it  is  required  to  set  the  step  values  manually.  This  can  be 

done in SETUP/STEPS (2.4.22.4). 

The STEPVALUE is showing the size of the capacitor, which is used for reactive power regulation. The func-

tion  of this value can be compared with the c/k value of power-factor control relays of former generations. 

The  STEPVALUE  is  shown  in  kvar.  Each  step  has  its  own  STEPVALUES,  at  BLR-Q(U)  it’s  one  per  step. 

Step database is working with two values of capacitor size. The value which is shown in kvar is the actual 

value. This is continuously corrected with every switching operation. A second value is saved after the first 

ten  switch  cycles  of  each  step  after  a  reset  of  step  database.  This  value  indicated  the  original  available 

STEPVALUE. This value is used to calculate the percentage of actual stepvalue to original stepvalue. This 

percentage gives very simple information about derating of the capacitor banks. 

2.3.3.1 

When automatic step recognition is not active, the percentage is not shown (2.4.23.5). 

2.4  Quickstart SETUP 

In this submenu basic settings can be made for the BLR-Q(U). These settings are neces-

sary for correct function and for correct display of the measurement values. This menu can 

be entered without password. 

The following parameters can be set in Quickstart menu: 

2.4.1  CHANGE LANGUAGE 

Standard version of BLR-Q(U) is supporting English, German and French. 

2.4.2  NOMINAL VOLTAGE 

Function of the setting of nominal voltage is to make a definition about the nominal voltage of the system. 

This nominal voltage is valid for normal control mode and voltage control mode. The threshold levels for 

under- and overvoltage are based on this as well as the ratings of the capacitor sizes in step database, 

which are used for control and monitoring (0 and 2.4.21.8). The capacitor sizes, which are stored in step 

database, are also rated to the nominal voltage.  

Independent of connection of the voltage measuring channel, nominal voltage is always the 

phase-phase voltage

! 

! 

Содержание BLR-Q(U) I/O








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды