manualshive.com logo in svg

Beluk BLR-Q(U) I/O, Справочное руководство

Поделиться
Скачать
Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 23

Technical Documentation 

 

    Rev. 01 

 
Power Factor Regulator 

BLR-Q(U)

 

 

Page 23 of 39 

 

2.4.23.10 CONTROL 

Four control modes can be selected: 

AUTO:

  

“Best Fit“ 

LIFO:

   

“Last in, first out“. 

1.  Threshold  level  of  each  step  is  checked  separately.  If  steps  have  different 

sizes, this can cause inaccuracy. 

2.  Step recognition is working in this mode as well, when it is active. If steps 

are  detected  as  defective,  they  are  skipped  in  this  mode.  If  this  is  not  ac-

cepted,  the  step  recognition  has  to  be  set  “OFF” and  capacitor  sizes  have 

to be programmed manually. 

Combi - Filter:

  This setting assures that in combined filters the connected power with higher degree 

of choking is higher as the power with lower degree of choking. 

Capacitors with higher degree of choking must be connected to the odd exits. 

Capacitors with smaller degree of choking must be connected to the even exits. 

Progressive:

  If more than one step is needed to reach target, the setting of switch interval is only 

valid for the first switching operation and the following steps are connected in short 

intervals.

 

2.4.23.11 Q OFFSET 

OFFSET of reactive power in kvar. This feature allows compensating a permanent reactive load, which can-

not be measured (e.g. a transformer). 

The offset of reactive power affects the readings of the following measuring values: 

current, reactive power, control deviation, apparent power, power factor PF and cos

ϕ

ϕ

ϕ

ϕ

. 

 

2.4.23.12 I < LIMIT FREEZE STEPS 

Yes: 

If current is detected as zero, the regulator is freezing all the steps until it can measure current again. 

No: 

If current is detected as zero, the regulator is switching-off the capacitors step by step with intervals of 

30 sec, to check for a broken cable until it can measure a current again. 

2.4.23.13 Q CAPACITIVE STEPS TURN OFF 

Disconnecting capacitors in leading power factor condition. 

2.4.23.14 Cos phi control 

Switch on or off voltage control 

COS PHI : U control reactive power depending on the voltage 

COS PHI : P control reactive power depending on the load 

NO : standard power factor control 

!

!

!

Содержание BLR-Q(U) I/O








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды