manualshive.com logo in svg

Beluk BLR-Q(U) I/O, Справочное руководство

Поделиться
Скачать
Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 14

Technical Documentation 

 

    Rev. 01 

 
Power Factor Regulator 

BLR-Q(U)

 

 

Page 14 of 39 

 

2.4.9.2 

DISCHARGE TIME 

For every single capacitor step an own discharging time can be defined. The discharging time is a blocking 

time, becoming active after switching off a step. As long as this time is running (display of "

!

" in the step indi-

cation) this step is not available for the regulation. Discharging time should be adapted to the capacitor dis-

charging unit.  

For step exits, which are switching thyristor switches, discharging time can be reduced to the zero. 

2.4.10 Cos phi control 

Switch on or off voltage control 

COS PHI : U control reactive power depending on the voltage 

COS PHI : P control reactive power depending on the load 

NO : standard power factor control 

The following items appears only when the cos phi control is set to COS Phi : U, otherwise the points 

are not visible. 

2.4.11 COS PHI CAP 

Defines the capacitive limit for the voltage control. 

2.4.12 COS PHI : U SET POINT 1 

Defines target point 1 for the COS PHI : U / COS PHI : P control 
 
SET POINT 1 uses the “COS PHI CAP” when the measured voltage is at the level which is adjusted. In fac-

tory setting this point is used when 0.98 * NOM. V 

2.4.13 COS PHI CENTER 

Defines the center point of the charachteristic given by the adjusted SET POINT’s 1-4 

2.4.14 COS PHI : U SET POINT 2 

Defines an further point on the charachteristic build between SET POINT 1 and SET POINT 4. This is also 

adjusted by a voltage Level 

2.4.15 COS PHI : U SET POINT 3 

Defines an further point on the charachteristic build between SET POINT 1 and SET POINT 4. This is also 

adjusted by a voltage Level 

2.4.16 COS PHI IND 

Defines the inductive limit for the voltage control. 

Содержание BLR-Q(U) I/O








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды