Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 26

Страница: 26 / 39

Technical Documentation

Rev. 01

Power Factor Regulator

BLR-Q(U)

Page 26 of 39

2.4.25 ALARM

In the following chapter all adjustable Alarms including trigger are listed.

Control alarm

Trigger

after 50x switching time not reaching the target cos

and

∆

Q > smallest step

(over-/under compensation)

No current

Trigger:

I < 15mA

Reaction:

switch off steps to reach current flow or freeze (2.4.23.12)

Step fault

Trigger:

step size detection not possible

Reaction:

alarm after three not successful trials in series (alarm delay 300 sec)

Step warning

Trigger:

a) Stepsize falls below an adjustable level (delay 300 sec). This level is

percentage between stepsize and nominal stepsize in step-database

b) switch cycles exceeding the adjustable limit for switch cycles.

COS PHI

Trigger:

The actual cos

is outside the adjustable range between

c0.80 and i0.80. The delay time can be adjusted from 1s to 36000s.

Harmonics U

Trigger:

THD U exceeds the adjusted limit between 1% and 99.9%.

Harmonics I

Trigger:

THD I exceeds the adjusted limit between 1% and 99.9%.

Overload P

Trigger:

amount of P exceeds the adjustable limit between 1kW and 99.9MW

Overload Q

Trigger:

amount of Q exceeds the adjustable limit between 1kvar and 99.9Mvar

P-export

Trigger:

alarm will be triggered as soon as kW export is recognized

Temp1 / Temp2:

Trigger:

ambient temperature exceeds the adjusted limit.

Over current:

Trigger:

I > 6Amps

It's not possible to deactivate this alarm.

BLR-Q(U) always generates a signal

via the display and alarmrelay.

Frequency alarm:

Trigger:

frequency is out of allowed range (max. range 45 – 65Hz, delay 10sec).

Over/Undervoltage:

Trigger:

Voltage is out of range. The limits depend on setting for nominal voltage

and on tolerance settings (0/ 2.4.21.8).

It's not possible to deactivate this alarm, but a bigger tolerance can be set!

In case of this alarm, the control stops, all steps are disconnected, the alarmrelay

gives signal and the “sad face” is shown.

Содержание BLR-Q(U) I/O








































Результаты поиска

Содержание BLR-Q(U) I/O

Отзывы:

Бренды по названию

Популярные бренды

Beluk BLR-Q(U) I/O, Справочное руководство

Результаты поиска

Содержание BLR-Q(U) I/O

Отзывы:

Бренды по названию

Популярные бренды