manualshive.com logo in svg

Beluk BLR-Q(U) I/O, Справочное руководство

Поделиться
Скачать
Beluk BLR-Q(U) I/O Скачать руководство пользователя страница 15

Technical Documentation 

 

    Rev. 01 

 
Power Factor Regulator 

BLR-Q(U)

 

 

Page 15 of 39 

 

2.4.17 COS PHI : U SET POINT 4 

Defines target point 4 for the COS PHI : U / COS PHI : P control 
 
SET POINT 4 uses the “COS PHI IND” when the measured voltage is at the level which is adjusted. In fac-

tory setting this point is used when 1.06 * NOM. V 

2.4.18 SETUP 

In  this  submenu  advanced  settings  can  be  made  for  the  BLR-Q(U).  These  settings  are 

necessary  for  individual  parametring  for  special  applications.  To  enter  this  submenu, 

please push the right button for 3 sec. It is protected by a password (factory setting 2402). 

The menu is divided into logical groups. In these groups you can find paramters which are also in Quickstart 

SETUP. The following points explain the settings. 

2.4.19 CHANGE LANGUAGE 

Standard version of BLR-Q(U) is supporting English, German and French. 

2.4.20 START AI 

See Chapter 2.4.5 

2.4.21 MEASUREMENT 

2.4.21.1  CT-FACTOR 

The CT FACTOR is the ratio of current transformer. (e. g. 1000/5 = ratio 200). At BLR-Q(U)3phase the CT-

Factor is used for all three current channels. 

For current measuring a CT always have to be used! 

2.4.21.2  VT-FACTOR 

VT FACTOR is the ratio of the voltage transformer. If the regulator is connected directly to the measurement 

voltage without VT the value 1 has to be used. 

2.4.21.3  NOMINAL VOLTAGE 

Function of the setting of nominal voltage is to make a definition about the nominal voltage of the system. 

The threshold levels for under- and overvoltage are based on this as well as the ratings of the capacitor 

sizes in step database, which are used for control and monitoring (0 and 2.4.21.8). 

Independent of connection of the voltage measuring channel, nominal voltage is always the 

phase-phase voltage

! 

2.4.21.4  CONNECTION MEASUREMENT 

CONNECTION  MEASUREMENT  the  setting  if  measuring  of  voltage  is  connected  between  two  phases  or 

between phase and neutral phase. It is normally detected automatically at every start of BLR-Q(U). This is 

done by comparing the setting NOMINAL VOLTAGE and the real measured voltage.  

! 

! 

Содержание BLR-Q(U) I/O








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды