Belarus 2122.6 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 248

background image

2122.6-0000010 OM

190

5.4.4 General maintenance services
5.4.4.1 General instructions
Carry out maintenance service operations listed in present subsection 5.4.4 as may

be necessary (i.

е

. according to corresponding pressure or dirtiness sensor indications).

5.4.4.2 Operation 79. Adjustment of valve setting operating pressure for

transmission hydraulics

The valve setting operating pressure for the transmission hydraulics is located on

duplex filter 7 (figure 5.4.2).

The valve setting operating pressure for the transmission hydraulics 3 (figure

5.4.32) maintains oil pressure in the transmission hydraulics within 1.1 to 1.2 MPa at rated
speed of the engine. If the pressure is permanently below 1.1 MPa or above 1.2 MPa with
the tractor warmed up and with the rated speed of the engine, then adjust valve 3 by
changing the number of washers 4 between spring 2 and valve setting the operating pres-
sure for transmission hydraulics 3. To do this it is necessary to screw valve 3 out of hous-
ing 1.

To increase the pressure it is required to increase the amount of washers, to reduce

the pressure it is required to reduce the amount of washers.

ATTENTION: THE TOTAL THICKNESS OF ADJUSTING WASHERS SHALL NOT

INCREASE 7 MM PER VALVE!

1 – duplex filter body; 2 – spring; 3 – valve setting operating pressure for transmis-

sion hydraulics; 4 – adjusting washers; 5 – lubrication valve; 6 – annunciator valve.

Figure 5.4.32

–

Adjustment of valve setting operating pressure for transmission hydraulics

ATTENTION: IF PRESSURE GOES BELOW 0.8 MPA, STOP THE TRACTOR AND

ELIMINATE THE FAILURE IN TRANSMISSION HYDRAULICS!

5.4.4.3 Operation 80. Change of duplex filter filtration package for

transmission hydraulics and rinse of mesh filter

The filtration package of the duplex filter for the transmission hydraulics 7 (figure

5.4.2) shall be changed as impurity annunciator 20 (figure 2.15.1) located on CECS goes
on.

ATTENTION: IT IS NECESSARY TO REPLACE TWO FILTRATION PACKAGES

SIMULTANEOUSLY!

https://tractormanualz.com/

«
...
188
189
190
191
192
...
»

Содержание 2122.6

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2122.6

Бренд: Sami Страницы: 10

Broadmoor 2600 Series

Бренд: Simplicity Страницы: 40

19B70054 Series

Бренд: Cub Cadet Страницы: 32

Бренд: Mahindra Страницы: 140

Бренд: Zetor Страницы: 142

Бренд: MTD Страницы: 33

Бренд: BUG-O Страницы: 30

Бренд: Takeuchi Страницы: 114

LS Tractor LW3150

Бренд: RadTech Страницы: 44

Бренд: Zetor Страницы: 182

FORTERRA HSX 100 2014

Бренд: Zetor Страницы: 250

Бренд: Komatsu Страницы: 405

Monogram ZCG3500DSS

Бренд: GE Страницы: 2

Бренд: Broan Страницы: 12

Бренд: Gaggenau Страницы: 24

Бренд: Yanmar Страницы: 4

Бренд: Montgomery Ward Страницы: 18

Бренд: Bush Hog Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды