Belarus 2122.6 Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 248

background image

2122.6-0000010 OM

167

5.4.1.4 Operation 3. Check of oil level in the HLL tank
Before checking oil level, set the tractor on the flat horizontal ground. Lower RLL links

to the extreme lower position. Stop the engine and engage the parking brakes.

HLL tank is located behind the rear left wheel.
Check the oil level visually according to oil level indicator 2 (figure 5.4.3) on tank 4. The

level shall be between the marks “O” and “

П

” of the oil level indicator. If necessary, refill the oil

up to the “

П

” mark through an oil filler neck, for which turn off plug 5.

While operating the tractor coupled with implements requiring higher oil consumption,

fill the oil up to the mark “C” on the oil level indicator with the hydraulic cylinder retracted rods
of the implement and the tractor.

1 – drain plug; 2 – oil lever indicator; 3 – hose of oil filler neck; 4 – HLL tank; 5 – cover of oil filler

neck.

Figure 5.4.3 – Check of oil level and change of oil in the HLL tank

ATTENTION: OIL LEVEL CHECKING OPERATION IN THE HYDRAULIC LIFT LINK-

AGE TANK SHALL BE CARRIED OUT ONLY WITH THE RETRACTED RODS OF RLL HY-
DRAULIC CYLINDERS AS WELL AS OF THE IMPLEMENTS COUPLED WITH THE TRAC-
TOR!

WARNING: BE CAUTIOUS TO AVOID CONTACT WITH HOT OIL!

5.4.1.5 Operation 4. Check of oil level in the HSC tank
Before checking oil level in the HSC tank 3 (figure 5.4.4), it is required to set the tractor

on flat horizontal ground. Stop the engine and engage the parking brakes.

The HSC oil tank is located in front, on front weights bracket, near the storage battery.
Check the oil level visually according to oil level indicator 1 on HSC tank 3. The level

shall be between the upper and lower marks of the oil level indicator. If necessary, remove plug
2 of the oil level indicator and refill the oil up to the oil level indicator upper mark. Put plug 2
back on its place.

1 – oil level indicator; 2 – plug; 3 – HSC tank.

Figure 5.4.4 – Check of oil level in HSC tank

WARNING: BE CAUTIOUS TO AVOID CONTACT WITH HOT OIL!

https://tractormanualz.com/

«
...
165
166
167
168
169
...
»

Содержание 2122.6

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2122.6

Бренд: Whirlpool Страницы: 4

Бренд: Whirlpool Страницы: 7

KIOTI UD28-A901AF

Бренд: Daedong Страницы: 11

Tractor TURBOMIX MTXH

Бренд: Bauer Страницы: 42

Бренд: Valtra Страницы: 518

PROXIMA PLUS 90 2012

Бренд: Zetor Страницы: 212

Бренд: Mahindra Страницы: 94

Бренд: Zetor Страницы: 233

Wheel Horse 523Dxi

Бренд: Toro Страницы: 60

Solo Comfort T 13-37.7 HD

Бренд: AL-KO Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды