Beckman Coulter Allegra 25R Скачать руководство пользователя страница 40

Страница: 40 / 56

4-2

Troubleshooting

Table 3-1. Error Messages

Error

Number

Problem

Result

Recommended Action

1 through 62,
69 through 77

Microprocessor or
mechanical error

Deceleration to full
stop; run cannot be
restarted until error
is cleared

After rotor comes to a complete stop turn
the power off, then wait 15 seconds before
turning it back on to reset.

Error during closing of door

Run cannot start

1. Remove debris from latch.
2. Close the door, pressing down gently.
3. Turn the power off, then wait 15 seconds

before turning it back on to reset.

Door open detected during
run

Maximum decelera-
tion to full stop

After rotor comes to a complete stop, close
the centrifuge door, turn the power off, then
wait 15 seconds before turning it back on to
reset.

82, 83

Door latch malfunction

Door does not open

See

RETRIEVING YOUR SAMPLE

, below.

Thermal cutoff switch
activated

Deceleration to full
stop

1. Turn the power off.
2. Check that ambient temperature is within

the specified limits (10 to 35°C).

3. Check, for air inlet and exhaust vent

obstruction. Clean air inlets and exhaust
vents.

4. After the motor has cooled down

(approximately 15 minutes with the door
open), turn the power on to reset the
thermal protector circuit.

85, 87

Chamber overtemperature

Deceleration to full
stop

1. Turn the power off.
2. Check that ambient temperature is within

the specified limits (10 to 35°C).

3. Check for air inlet and exhaust vent

obstruction. Clean air inlets and exhaust
vents.

4. After the motor has cooled down

(approximately 15 minutes with the door
open), turn the power on to reset the
thermal protector circuit.

90 through 96

Defective sensor

Deceleration to full
stop

Turn the power off, then wait 15 seconds
before turning it back on to reset.

98, 99

Incorrect rotor identification

Deceleration to full
stop

Input correct rotor identification.

Содержание Allegra 25R
























































Результаты поиска

Содержание Allegra 25R

Отзывы:

Beckman Coulter Allegra 25R, Инструкция по эксплуатации, Страница: 40 / 56

Результаты поиска

Содержание Allegra 25R

Отзывы: