Beckman Coulter Allegra 25R Скачать руководство пользователя страница 36

Страница: 36 / 56

3-8

Operation

Action

Result

1. Check that all parameters

are correct and the door is
closed.

CAUTION

Do not lift or move the centrifuge while the rotor
is spinning.

2. Press [

START

• The

SPEED

display indicates rotor speed in rpm. (You can check

the RCF by pressing the [

RCF

] key.)

• A blinking LED at the bottom of the

TIME

display indicates that

the run is in progress. This display also shows the remaining run
time in hours and minutes for a timed run (when the

TIME

display

reaches 0, the run ends); or the infinity symbol (

∞

) and time

elapsed since the run start for a continuous run. (When the elapsed
time reaches 9 hours, 59 minutes during a continuous run, it resets
to 0 and continues counting until [

STOP

] or [

FAST STOP

] is pressed.)

• The

ACC/DEC

display shows the deceleration rate selected for

the run.

WARNING

Do not attempt to override the door interlock
system while the rotor is spinning.

CHANGING PARAMETERS DURING A RUN

While a run is in progress, parameters can be altered without stopping
the run:

• Speed can be decreased or increased, not to exceed the maximum

rated rotor speed.

• Temperature can be decreased or increased.

• Time can be changed from a specified time period to continuous,

or a continuous run can be changed to a timed run.

• Run duration of a timed run can be shortened or extended.

Содержание Allegra 25R
























































Результаты поиска

Содержание Allegra 25R

Отзывы:

Beckman Coulter Allegra 25R, Инструкция по эксплуатации, Страница: 36 / 56

Результаты поиска

Содержание Allegra 25R

Отзывы: