Beckman Coulter Allegra 25R Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

Beckman Coulter Allegra 25R Скачать руководство пользователя страница 35

3-7

Operation

Table 3-1. Acceleration and Deceleration Rates (in Minutes:Seconds) to and from Maximum Speed.

Times shown are for the TS-5.1-500 rotor, with the rotor fully loaded, to/from maximum rotor speed of 5000 rpm.

(Times are approximate; actual times will vary depending on the rotor in use,

the rotor load, run speed, and voltage fluctuations.)

Setting Deceleration Rate

Action

Result

1. Press [

DECEL

]. The

ACC/DEC

display flashes.

2. Press [

S

] or [

T

]

until the

required deceleration rate
appears, then press [

ENTER

].

Entered number appears on the

ACC/DEC

display.

STARTING A RUN

You can start the run with parameters in memory from the previous
run, or using new or changed parameters that you enter using the
procedure described above.

Accel/Decel Rate

Accel

Decel

9
8
7

00:59
01:19
01:39

00:57
01:17
01:37

6
5
4

01:59
02:19
03:19

01:57
02:17
02:37

3
2
1
0

03:59
04:19
04:39
04:59

02:57
03:17
03:27

coast

«
...
33
34
35
36
37
...
»

Содержание Allegra 25R

























































Отзывы:

Нет отзывов