Beckhoff CU8130-0240 Скачать руководство пользователя

Страница: 44 / 57

Configuration

CU8130-0240

Version: 1.1

Requirements

Development en-
vironment

Target platform

UPS hardware

PLC libraries to be
integrated (cate-
gory group)

TwinCAT v3.1.0

PC or CX (x86, x64, ARM)

• Beckhoff BAPI v1;

• Beckhoff P24Vxxxx;

• Beckhoff CP903x card (PCI/ISA);

• Beckhoff CX2100-09x4 models

(e.g. CX2100-0904 or
CX2100-0914 + "Smart Battery"
CX2900-0192);

• The APC devices that come

supplied with Beckhoff Industrial
PC support the Smart protocol
and can be configured with the
Windows UPS service.

Tc2_IoFunctions
(IO)

7.5.5

E_UpsPowerStatus

Status of the power supply.

TYPE E_UpsPowerStatus :
(
    PowerUnknownStatus,
    PowerOnLine,
    PowerOnBattery
);
END_TYPE

Name

Value

Meaning

PowerUnknownStatus

The status of the power supply is
unknown

PowerOnLine

Mains power supply.

Battery power supply.

Requirements

Development en-
vironment

Target platform

UPS hardware

PLC libraries to be
integrated (cate-
gory group)

TwinCAT v3.1.0

PC or CX (x86, x64, ARM)

• Beckhoff BAPI v1;

• Beckhoff P24Vxxxx;

• Beckhoff CP903x card (PCI/ISA);

• Beckhoff CX2100-09x4 models

(e.g. CX2100-0904 or
CX2100-0914 + "Smart Battery"
CX2900-0192);

• The APC devices that come

supplied with Beckhoff Industrial
PC support the Smart protocol
and can be configured with the
Windows UPS service.

Tc2_IoFunctions
(IO)

Содержание CU8130-0240


























































Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды

Beckhoff CU8130-0240, Руководство пользователя

Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды