Beckhoff CU8130-0240 страница 42 Скачать руководство пользователя

Страница: 42 / 57

Configuration

CU8130-0240

Version: 1.1

Status in-
formation

Beckhoff BAPI
v1

Beckhoff
P24Vxxxx UPS

Beckhoff 24V
UPS on the
CP903x card

CX2100-09x4

APC
Back-
UPS
Pro
280

APC
Smart-
UPS 420

Description

pired. Imple-
mented in the
UPS software
version >=
3.0.0.8;

Under Tempera-
ture

(bit 11 set)

was detected and
the charging of the
battery was inter-
rupted.

Requires a newer
(second) hard-
ware revision.

Im-

plemented in the
UPS software ver-
sion >= 3.0.0.18.

Fuse Not Ok

(bit

12 set). The
"Smart Battery"
fuse is defective or
not available.

Re-

quires a newer
(second) hard-
ware revision.

Im-

plemented in the
UPS software ver-
sion >= 3.0.0.18.

Requirements

Development en-
vironment

Target platform

UPS hardware

PLC libraries to be
integrated (cate-
gory group)

TwinCAT v3.1.0

PC or CX (x86, x64, ARM)

• Beckhoff BAPI v1;

• Beckhoff P24Vxxxx;

• Beckhoff CP903x card (PCI/ISA);

• Beckhoff CX2100-09x4 models

(e.g. CX2100-0904 or
CX2100-0914 + "Smart Battery"
CX2900-0192);

• The APC devices that come

supplied with Beckhoff Industrial
PC support the Smart protocol
and can be configured with the
Windows UPS service.

Tc2_IoFunctions
(IO)

Содержание CU8130-0240


























































Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды

Beckhoff CU8130-0240, Руководство пользователя

Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды