Beckhoff CU8130-0240 страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 57

background image

Commissioning

CU8130-0240

21

Version: 1.1

6.3

Communication

There are several ways to communicate with the UPS, for example to query the status or to control the
device state until shutdown.

The following options are available:

• Protocol-based communication via UPS-OCT (One Cable Technology) or USB.

• Digital signals for communication with non-protocol-capable end devices.

• TwinCAT PLC function blocks for querying the UPS operation.

The configuration and diagnosis of the UPS-OCT or USB communication method is carried out via the
Beckhoff UPS software on Windows 7 or Windows 10.

6.3.1

Connection via UPS-OCT

A special feature of the Beckhoff CU8130-0240 UPS is OCT (One Cable Technology) as a communication
technology between UPS and Industrial PC. The two connection cables (+24 V, 0 V) between the Industrial
PC and the UPS are used to supply power to the Industrial PC and for bidirectional, modulated data
transmission.

Fig. 11: Example of a connection via UPS-OCT with a CU8130-0240 UPS and a CX5240 Embedded PC.

Only the U1out interface of the UPS supports UPS-OCT communication. If you wish to use the UPS-OCT
technology, you must ensure that the Industrial PC supports UPS-OCT. You can use the U1out interface to
retrieve status data for diagnostic purposes or to configure the UPS.

«
...
19
20
21
22
23
...
»

Содержание CU8130-0240


























































Отзывы:

Нет отзывов

Похожие инструкции для CU8130-0240

Бренд: National Flooring Equipment Страницы: 49

Бренд: National Flooring Equipent Страницы: 33

Бренд: Laser Страницы: 2

Бренд: MAC TOOLS Страницы: 44

Бренд: Rapid Страницы: 93

Бренд: Rapid Страницы: 140

Бренд: RIDGID Страницы: 40

Бренд: REAC Страницы: 15

Бренд: Gude Страницы: 20

Бренд: G-Scale Graphics Страницы: 4

Бренд: SilverBolt Страницы: 9

Бренд: Chicago Pneumatic Страницы: 36

Бренд: joke Страницы: 12

Бренд: F.F. Group Страницы: 32

NetSure 722NBBB

Бренд: Vertiv Страницы: 60

Бренд: TAKASAGO Страницы: 192

Бренд: Kaindl Страницы: 9

Бренд: Hander Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды