Beckhoff CU8130-0240 Скачать руководство пользователя

Страница: 45 / 57

Error handling and diagnostics

CU8130-0240

Version: 1.1

Error handling and diagnostics

Table 9: Diagnostics LED, Uin.

LED

Color

Description

Uin

Green

Input voltage Uin is present and is within the defined limits between 24.4 V
and 28.8 V.

Red

Input voltage Uin is below 20.4 V. UPS is switched in the UPS mode
(undervoltage protection).

Yellow

Input voltage Uin is over 28.8 V. UPS is switched in the UPS mode
(overvoltage protection).

Table 10: Diagnostics LED, Uout.

LED

Color

Description

Uout

Green

Output voltage Uout present.

Red

Output voltage Uout switched off.

Yellow

Output voltage Uout is above 28.8 V.

Table 11: Diagnostics LED, DIAG.

LED

Color

Description

DIAG

Off

No input voltage Uin present. UPS is not initialized.

White

No battery module or capacitor board found.

White, Red or
White, Green
flashing

White: timer for shutdown is active.
Red: in case of discharge.
Green: intentional shutdown.

Red

No input voltage Uin present. UPS is not being charged.

Blue, Red

Input voltage Uin present but no battery module.

Blue, Magenta

Battery module does not match the UPS.

Green, flashing UPS is being charged.

Green, Yellow

UPS is below or above the allowed ambient temperature.

Green

Input voltage Uin present. UPS is ready for operation and charged.

Red, flashing

No input voltage Uin. UPS mode started and UPS is being discharged.

Содержание CU8130-0240


























































Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды

Beckhoff CU8130-0240, Руководство пользователя

Результаты поиска

Содержание CU8130-0240

Отзывы:

Похожие инструкции для CU8130-0240

Бренды по названию

Популярные бренды